0.5mm Pitch Floating BTB
Connector (BA21&BA22) Specification
Rev. Document No. SHEET
B
E-EDBA-0009
Page1 of 7
FMEN-058A
1. Scope(适用范围）
This product specification contains the test method, the general performance and property for
0.5mm pitch floating BTB (BA21 & BA22) connector series.
2. General items（一般项目）
2.1 Operating Temperature Range: -40 ºC ~105 ºC
2.2 Storage Temperature Range: -10 ºC ~+40 ºC
2.3 Test Conditions: Unless otherwise specified, the tests and measurements are to be carried out
in the following standard conditions.
Temperature: 20ºC+5ºC; Relative Humidity: 25%~85%; Air pressure: 86~106 Kpa
3. Property（性能）
3.1 Materials（材质）
Item（项目） Requirements（标准）
Housing（主体） High Temperature Thermoplastic（高温料）, UL 94V-0
PAD(吸附片） High Temperature Thermoplastic（高温料）, UL 94V-0
Contact（端子） Copper Alloy（铜合金）
Clip（固定片）
Copper Alloy（铜合金）
3.2 Ratings（规格��
Item（项目） Requirements
Current Rating（额定电流） Power contact:3A/pin，Signal cotact:0.5A/pin
Approved By:
Ady zhou
Checked By:
Peiguang Xu
Written By:
Peak
DATE:
2021.10.20
DATE:
2021.10.20
DATE:
2021.10.20
環保要求
符合 RoHS 2.0 規定
0.5mm Pitch Floating BTB
Connector (BA21&BA22) Specification
Rev. Document No. SHEET
B
E-EDBA-0009
Page2 of 7
FMEN-058A
4. Appearance, construction and dimension(外观、结构和尺寸）:
4.1 Appearance
Each area must be finished well and have no rust, scratches, cracks and inferior or
peeling of plating, etc. that may be harmful in terms of product functioning.
4.2 Construction and dimensions
Product shall meet construction and physical dimensions specified in the applicable product
drawing.
5. Test Methods and Requirements（测试方法和要求）:
5.1 Electrical Performance（电气性能）
Item
（序
号）
Test Item
（测试项目）
Standard（标准） Requirement(规格要求）
5.1.1
Low Level
Contact
Resistance
(接触阻抗）
It should be tested in accordance with
(EIA-364-23C).
Signal :70 mΩ max.
Power :20 mΩ max.
5.1.2
Insulation
Resistance
(绝缘阻抗）
Apply a voltage of DC xxV (Signal :100V；
Power:250V）for 1 minute between
adjacent terminals and measure.
(EIA-364-21C).
Signal :100 MΩ min.
Power :1000 MΩ min.
5.1.3
Dielectric
Withstanding
Voltage
(耐电压）
Apply a voltage of AC xxV(Signal :150V；
Power:600V）for 1 minute between
adjacent terminals.
(EIA-364-20C).
No evidence of
Breakdown and flashover or
leakage current over 0.5mA.
5.2 Mechanical Performance（机械性能）:
5.2.1
Contact
Retention Force
（端子保持力）
Pull contacts at maximum rate of
25mm/minute.
(EIA-364-29C)
100 gf min. per contact.
5.2.2
Insertion Force
（插入力）
Insert plug into socket at a constant speed
of 25mm/minute.
(EIA-364-13D)
100 gf max. per contact.
5.2.3
Withdrawal Force
(拔出力）
Pull plug out from socket at a constant
speed of 25mm/minute (EIA-364-13D)
5 gf min. per contact.
5.2.4
Durability
(耐久）
The sample should be mounted in the
tester and fully mated and unmated 100
cycles as specified at rate of 25 mm/min.
(EIA-364-09C)
LLCR:
Signal :80 mΩ max.
Power :30 mΩ max.