REVISIONS

LTR DESCRIPTION DATE (YR-MO-DA) APPROVED

Update drawing to reflect currents requirements.

05-01-20

Raymond Monnin

Figure 2, correct ter mi nal symbols for case outlines N, T, U, and Z.

Add note to table II, Group C end-poi nt test para met er s. -gz

09-07-06

Charles F. Saffle

Updated drawing paragraphs. -sld

12-05-15

Charles F. Saffle

REV

SHEET

REV

SHEET

REV STATUS REV C C C C C C C C C C C C

OF SHEETS

SHEET

PMIC N/A PREPARED BY

Gary Zahn

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

http://www.landandmaritime.dla.mil/

STANDARD

MICROCIRCUIT

DRAWING

CHECKED BY

Michael C. Jones

THIS DRAWING

IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

APPROVED BY

Kendall A. Cottongim

MICROCIRCUIT, LINEAR, VOLTAGE

REGULATOR, 5 VOLT, POSITIVE, FIXED,

MONOLITHIC SILICON

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

DRAWING APPROVAL DATE

99-07-14

AMSC N/A

REVISION LEVEL

SIZE

CAGE CODE

67268

5962-98643

SHEET

1 OF

DSCC FORM 2233

APR 97

5962-E170-12

STANDARD

MICROCIRCUIT DRAWING

SIZE

5962-98643

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

REVISION LEVEL

SHEET

DSCC FORM 2234

APR 97

1. SCOPE

1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-3853 4. A

choice of case outlin es and le ad finishes which are available and are reflected in the Part or Identifying Number (PIN). When

available, a choice of radiation hardness assurance levels are reflected in the PIN.

1.2 PIN. The PIN shall be as shown in the following example:

5962

98643

Federal

stock class

designator

RHA

designator

(see 1.2.1)

Device

type

(see 1.2.2)

Device

class

designator

Case

outline

(see 1.2.4)

Lead

finish

(see 1.2.5)

\ /

(see 1.2.3)

Drawing number

1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RH A

levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.

1.2.2 Dev ice ty pe(s). The device type(s) identify the circuit function as follows:

Device type Generic number 1/ Circuit function

01 SDP7805A Positive voltage regulator, 5 volt, fixed

1.2.3 Dev ice cl as s designator. This device class designator shall be a single letter identifying the product assurance level.

All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,

and E) or QML Listing (Class G and D). The product assurance levels are as follows:

Devi ce class Device performance documentation

K Highest reliability class available. This level is intended for use in space

applications.

H Standard military quality class level. This level is intended for use in applications

where non-space high reliability devices are required.

G Reduced testing version of the standard military quality class. This level uses the

Class H screening and In-Process Inspections with a possible limited temperature

range, manufacturer specified incoming flow, and the manufacturer guarantees (but

may not test) periodic and conformance inspections (Group A, B, C, and D).

E Designates devices which are based upon one of the other classes (K, H, or G)

with exception(s) taken to the requirements of that class. These exception(s) must

be specified in the device acquisition document; therefore the acquisition document

should be reviewed to ensure that the exception(s) taken will not adversely affect

system performance.

D Manufacturer specified quality class. Quality level is defi ned by the manufact urers

internal, QML certified flow. This product may have a limited temperature range.

The SDP7805A is similar to the 7805A listed on Standard Microcircuit Drawing 5962-87782.