REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Paragraph 1.3 corrected the Output current (I
OUT
) from 2.0 A to 3.0 A.
Updated drawing to reflect current requirements. -sld
02-08-27
Raymond Monnin
B
Update draw ing. -gz
07-01-09
Joseph Rodenbeck
C
Updated drawing paragraphs. -sld
12-05-15
Charles F. Saffle
REV
SHEET
REV
SHEET
REV STATUS
C
C
C
C
C
C
C
C
C
C
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10
PMIC N/A PREPARED BY
Gary Zahn
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Michael C. Jones
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Kendall A. Cottongim
MICROCIRCUIT, LINEAR, VOLTAGE
REGULATOR, POSITIVE, ADJUSTABLE, LOW
DROPOUT, MONOLITHIC SILICON
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
99-07-06
AMSC N/A
REVISION LEVEL
C
SIZE
A
CAGE CODE
67268
5962-98649
SHEET
1 OF
10
DSCC FORM 2233
APR 97 5962-E172-12
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-98649
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
C
SHEET
2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962 - 98649 01 H T X
Federal RHA Device Device Case Lead
stock class designator type class outline finish
designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5)
\ / (see 1.2.3)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Dev ice ty pe(s). The device type(s) identify the circuit function as follows:
Device type Generic num ber 1/ Circuit function
01 SDP1085 3.0 A, positive voltage regulator, adjustable, low dropout
1.2.3 Dev ice cl as s designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Devi ce class Device performance documentation
K Highest reliability class available. This level is intended for use in space
applications.
H Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufa ctur er specif ie d incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1/ The SDP1085 is similar to the LT1085 and OM1850 listed on Standard Microcircuit Drawing 5962-88646.