Note: The application and performance property val-
ues above are typical for the material, but not intend-
ed for use in specifications or for acceptance inspec-
tion criteria because of variations in testing methods,
conditions and configurations.
Surface Preparation
Immediately before applying sealant to primed sub-
strates, the surfaces should be cleaned with solvents.
Contaminants such as dirt, grease, and/or processing
lubricants must be removed prior to sealant applica-
tion.
A progressive cleaning procedure should be employed
using appropriate solvents and a new lint-free cloth
conforming to AMS 3819. (Reclaimed solvents or tis-
sue paper should not be used.) Always pour solvent
on the cloth to avoid contaminating the solvent sup-
ply. Wash one small area at a time.
It is important that the surface is dried with a second
clean cloth prior to the solvent evaporating to prevent
the redeposition of contaminants on the substrate.
Substrate composition can vary greatly. This can affect
sealant adhesion. It is recommended that adhesion
characteristics to a specific substrate be determined
prior to application on production parts or assemblies.
For a more thorough discussion of proper surface
preparation, please consult the SAE Aerospace
Information Report AIR 4069. This document is avail-
able through SAE, 400 Commonwealth Avenue,
Warrendale, PA 15096-0001.
Packing Options
P/S 895 Class B is supplied in two-part kits and
Semco
®
cartridges.
Mixing Instructions
Mix according to the ratios indicated in the applica-
tion properties section. Mix Part A and Part B sepa-
rately to uniformity, then thoroughly mix entire con-
tents of both parts of kit together taking care to
avoid leaving unmixed areas around the sides or bot-
tom of the mixing container.
Semco is a trademark of PRC-DeSoto International, Inc., registered with the U.S. Patent Office.
All recommendations, statements, and technical data contained herein are based on tests we believe to be reliable
and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a war-
ranty, either expressed or implied. User shall rely on his own information and tests to determine suitability of the
product for the intended use and assumes all risks and liability resulting from his use of the product. Seller’s and manu-
facturer’s sole responsibility shall be to replace that portion of the product of this manufacturer which proves to be
defective. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss, or dam-
age directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements other
than those contained in a written agreement signed by an officer of the manufacturer shall not be binding upon the
manufacturer or seller.
Printed in U.S.A.
Storage Life
The storage life of P/S 895 Class B is at least 9
months when stored at temperatures below 80°F
(27°C) in original, unopened containers.
Health Precautions
This product is safe to use and apply when recom-
mended precautions are followed. Before using this
product, read and understand the Material Safety
Data Sheet (MSDS), which provides information on
health, physical and environmental hazards, handling
precautions and first aid recommendations. An MSDS
is available on request. Avoid overexposure. Obtain
medical care in case of extreme overexposure.
For industrial use only. Keep away from children.
For emergency medical information call
1-800-228-5635.
Additional information can be found at:
www.ppgaerospace.com
For sales and ordering information call
1-800-AEROMI
X (237-6649).
P/S 895 Class B Aerodynamic Smooting Sealant
PRC-DeSoto International, Inc.
12780 San Fernando Road
Sylmar, CA 91342
Telephone (818) 362-6711
Toll Free (800) AEROMIX
www.ppgaerospace.com
Issue Date: 09/09
Supersedes: 06/09
Lit: 0137