Programmer for programmable encoders ETA PM and HTA PM
Series PRO
MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich
Tel.: +49 89 46094-0 ▪ www.megatron.de ▪ info@megatron.de
Date: 06/28/2022
Page: 1 of 2
Specications are subject to change without notice
Data Sheet for sensor accessories
Programmer for parameterization of Hall Multi-/single
turn rotary encoders of series ETA25PM, HTA36PM and
HTA25PM
Allows the parameterization of one rotary encoder 10.000
times
3 x Ø 4 mm sockets (for banana plugs) for power supply
and output signal
6 cable terminals for a fast and secure electrical connec-
tion of the rotary encoder
2 buttons (start/stop) for parameterizing the eective
electrical angle of rotation
DIP switch for setting the sense of rotation CW or CCW
The programmer enables the uncomplicated,
fast and safe parameterization of encoders of the
MEGATRON series ETA25PM, HTA36PM and HTA25PM,
which can be adjusted exactly for the purpose of the
encoder in the application. For quick electrical connection
of the sensor, the programmer has clamp contacts with
actuation buttons, which is particularly useful for series
parameterization.
Order Information:
Order no.: Order code:
135945 Programmer Tool for ETA HTA PM
Electrical Data
Programmable eective electrical angle of rotation 0..10° to 0..72000° (max. 200 turns)
Supply voltage 9 to 30 V for angle sensor output 0 to 5 V
15 to 30 V for angle sensor output 0 to 10 V
11 to 30 V for angle sensor with output 4 to 20 mA
Power consumption Not measurable if rotary encoder is not connected
With connected rotary encoder < 10 mA
Output load ≥ 5 kOhm
Electrical connection to the sensor 6 pol. terminal block with push buttons,
pitch 3.5 mm, wire gauge max. 1.5 mm²
Electrical connection for supply voltage and output
signal
3 x Ø 4 mm sockets, applicable for spring-loaded
Ø 4 mm plugs with rigid insulating sleeve (banana plug)
Maximum number of programming cycles 10000 times (per connected rotary encoder)
Mechanical and Environmental Data
IP protection grade (IEC 60529): IP00
Operating temperature 0 °C...+35 °C
Storage temperature -20 °C...+45 °C
Included in delivery Programming device
(no further components included in delivery)
Mass app. 32 g
Programmer for programmable encoders ETA PM and HTA PM
Series PRO
MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich
Tel.: +49 89 46094-0 ▪ www.megatron.de ▪ info@megatron.de
Date: 06/28/2022
Page: 2 of 2
Specications are subject to change without notice
Data Sheet for sensor accessories
Connection Matrix
Function Connection to Connections at
the programmer
Marking on
the
programmer
Colours of the
cable terminals
at the
programmer
Rotary
encoder
cable sheath
colour
VSUP 1 Programmer Ø 4 mm socket VSUP red -
OUT 1 Programmer Ø 4 mm socket OUT yellow -
GND 1 Programmer Ø 4 mm socket GND black -
VSUP 2 Rotary encoder Clamping terminal VSUP grey red
GND 2 Rotary encoder Clamping terminal GND grey black
OUT 2 Rotary encoder Clamping terminal OUT grey brown
SENSE OF ROTATION
(CW/CCW)
Rotary encoder Clamping terminal DIR grey orange
START point (0°) Rotary encoder Clamping terminal START grey yellow
END point (XXXX°) Rotary encoder Clamping terminal END grey green
CABLE SHIELD
(only HTA36PM,
HTA25PM, HTA25KPM)
Rotary encoder none
(cable shield won´t
be connected to the
programmer)
- - -
The programming instruction manual can be found on the MEGATRON website at the corresponding sen-
sor series (ETx25, ETx25K, ETx25F, HTx36, HTx25, HTx25K)