Programmer for MAB36APM, MAB40APM, ETA25PM
Series PRO
MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich
Tel.: +49 89 46094-0 ▪ www.megatron.de ▪ info@megatron.de
Date: 12/08/2021
Page: 1 of 2
Specications are subject to change without notice
Data Sheet for sensor accessories
Plug & Play programmer for parameterization of Hall
Single-/Multiturn rotary encoders from series MAB36APM,
MAB40APM, ETA25PM
Allows the parameterization of one rotary encoder 10.000
times
3 lateral positioned Ø 4 mm sockets (for banana plugs) for
power supply and output signal
6 cable terminals on top with push buttons for a fast and
secure electrical connection of the rotary encoder
2 buttons (start/stop) for parameterizing the eective
electrical angle of rotation
Toggle switch for setting the sense of rotation CW or
CCW
The programmer oers the easy, fast and secure
parameterization of MEGATRON`s MAB40APM,
MAB36APM and ET25PM rotary encoders. With the
programmer the rotary encoder can be parameterized exact
to the requirements of the application. The programmer
oers for a fast electrical connection of the rotary encoder
a cable terminal with push buttons, which is useful in
particular in a series parameterization.
Picture shows programmer with connected rotary
encoder. The rotary encoder is not part of delivery.
Order Information:
Order no.: Order code:
127813 Programmer MAB36APM, MAB40APM, ETA25PM
Electrical Data
Programmable eective electrical angle of rotation 0..10° to 0..72000° (max. 200 turns)
Supply voltage 9..30 V for rotary encoder with VSUP = 24 V and 0..5 V output
5..30 V for rotary encoder with VSUP = 24 V and 0..10 V output
Power consumption Not measurable if rotary encoder is not connected
With connected rotary encoder < 10 mA
Output load ≥ 5 kOhm
Electrical connection to the sensor 6 pol. terminal block with push buttons,
pitch 3.5 mm, wire gauge max. 1.5 mm²
Electrical connection for supply voltage and output signal 3 x Ø 4 mm sockets, applicable for spring loaded
Ø 4 mm plugs with rigid insulating sleeve (banana plug)
Maximum number of programming cycles 10000 times (per connected rotary encoder)
Mechanical and Environmental Data
IP protection grade (IEC 60529): IP 20
Operating temperature 0 °C...+35 °C
Storage temperature -20 °C...+45 °C
Material housing ABS (UL94-HB)
Included in delivery Programming device
(no further components included in delivery)
Mass app. 60 g
Programmer for MAB36APM, MAB40APM, ETA25PM
Series PRO
MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich
Tel.: +49 89 46094-0 ▪ www.megatron.de ▪ info@megatron.de
Date: 12/08/2021
Page: 2 of 2
Specications are subject to change without notice
Data Sheet for sensor accessories
Connection Assignment
Connection Matrix:
Function: Connection to: Connections at
the programmer:
Marking on
the
programmer:
Colours of the
cable terminals
at the programmer:
Rotary encoder
cable sheath
colour
VSUP 1 Programmer Ø 4 mm socket VSUP red -
OUT 1 Programmer Ø 4 mm socket OUT yellow -
GND 1 Programmer Ø 4 mm socket GND black -
VSUP 2 Rotary encoder Clamping terminal VSUP grey red
GND 2 Rotary encoder Clamping terminal GND grey black
OUT 2 Rotary encoder Clamping terminal OUT grey brown
SENSE OF ROTATION
(CW/CCW)
Rotary encoder Clamping terminal DIR grey orange
START point (0°) Rotary encoder Clamping terminal START grey yellow
END point (XXXX°) Rotary encoder Clamping terminal END grey green
CABLE SHIELD
(Only MAB36APM,
MAB40APM)
Rotary encoder none
(cable shield won´t
be connected to the
programmer)
- - -
Icon picture of programmer
The programming instruction manual can be found on MEGATRON`s homepage on the web
pages of the corresponding sensor series (MAB36APM, MAB40APM, ETA25PM)