Description
The HDU150 is an attractive, dynamic, all-
purpose microphone ideally suited for a
wide variety of vocal and sound reinforce-
ment applications.
Features
• Cardioid pickup pattern
• Crisp, clear sound
• Wide dynamic range with high-end sparkle and minimum
feedback
• Rigid, low noise cable-mount system
• Low sensitivity to breath and popping sounds
• Durable ball-shaped design
• Rubber shock-mount system for attenuation of handling and
cable noise
• Lockable, silent on/off reed switch
• Includes mic clip
Specifications
MIC Type: Handheld
Element: Moving coil dynamic
Polar Pattern: Cardioid
Impedance: 500-ohm
Frequency Response: 70 Hz to 15 kHz
Sensitivity*: -70 dB +/- 3dB
S/N Ratio: >65 dB
Connector: XLR Male
Switch: With sliding-type on/off switch
(lockable, silent reed switch)
Dimensions: 6-
1
/2" D x 1-
1
/2" Dia.
Product Weight: 13 oz.
Material: Zinc die cast
Finish: Rubberized black finish
* (0dB=1V/μ BAR 1,000 Hz indicated by open circuit)
HDU150 - Handheld Stage
Polar Graph
Frequency Response Graph
2
7
Description
The HDO100 is an attractive,
dynamic microphone perfectly-suited
for public address applications and
instrument sound reproduction.
Features
• Omni-directional pickup pattern
• Uniform pickup of sound from all directions with no
deterioration in frequency response
• Clean, clear reproduction with minimal ambient sound
• Low sensitivity to handling noise and stage vibrations
• Rugged, reliable construction
• Internal rubber shock isolation system
• Lockable, silent on/off reed switch
• Includes mic clip
Specifications
MIC Type: Handheld
Element: Moving coil dynamic
Polar Pattern: Omni-directional
Impedance: 500-ohm
Frequency Response: 70 Hz to 15 kHz
Sensitivity*: -72 dB +/- 3dB
S/N Ratio: >65 dB
Connector: XLR Male
Switch: With silent on/off switch
(lockable, silent reed switch)
Dimensions: 6-
1
/2" D x 1-
1
/2" Dia.
Product Weight: 13 oz.
Material: Zinc die cast
Finish: Rubberized black finish
* (0dB=1V/μ BAR 1,000 Hz indicated by open circuit)
HDO100 - Public Address
Polar Graph
Frequency Response Graph
Architect and Engineer Specifications
HDU250 - The microphone shall be a Bogen Model HDU250.
It shall be a cardioid, dynamic handheld microphone with a frequency
response of 50 Hz to 18 kHz and a 250-ohm impedance. The sensi-
tivity shall be -72 dB (+/- 3dB) and the signal-to-noise ratio greater
than 65 dB. It shall have a sliding-type on/off switch and a rubberized
black finish. The HDU250 shall have an XLR Male connector.
Dimensions shall be 7" D x 2" Dia. Weight shall be 13 oz.
HDU150 - The microphone shall be a Bogen Model HDU150.
It shall be a cardioid, dynamic handheld microphone with a frequency
response of 70 Hz to 15 kHz and a 500-ohm impedance. The sensi-
tivity shall be -70 dB (+/- 3dB) and the signal-to-noise ratio greater
than 65 dB. It shall have a sliding-type on/off switch and a rubberized
black finish. The HDU150 shall have an XLR Male connector.
Dimensions shall be 6-
1
/2" D x 1-
1
/2" Dia. Weight shall be 13 oz.
HDO100 - The microphone shall be a Bogen Model HDO100.
It shall be an omni-directional, dynamic handheld microphone with a
frequency response of 70 Hz to 15 kHz and a 500-ohm impedance. The
sensitivity shall be -72 dB (+/- 3dB) and the signal-to-noise ratio greater
than 65 dB. It shall have a silent on/off lockable reed switch and a rub-
berized black finish. The HDO100 shall have an XLR Male connector.
Dimensions shall be 6-
1
/2" D x 1-
1
/2" Dia. Weight shall be 13 oz.
DDU250 - The microphone shall be a Bogen Model DDU250. It shall
be a cardioid, dynamic desktop microphone with a frequency response
of 100 Hz to 12 kHz and a 500-ohm impedance. The sensitivity shall
be -76 dB (+/- 3dB) and the signal-to-noise ratio greater than 65 dB.
It shall have a push-to-lock/push-to-talk switch and a matte black finish.
It shall have a 10', 4-conductor, 2-shielded cable. Dimensions shall be 4-
1
/4" W x 18-
1
/4" H x 6-
1
/4" D. Weight shall be 3-
1
/2 lb.
GCU250 - The microphone shall be a Bogen Model GCU250. It
shall be a cardioid, back electret condenser gooseneck microphone
with a frequency response of 50 Hz to 18 kHz and a 250-ohm
impedance. The sensitivity shall be -65 dB (+/- 3dB) and the signal-
to-noise ratio greater than 65 dB. Max SPL @ 1% THD shall be
greater than 130 dB. It shall have a non-glare black finish. The
GCU250 shall have an XLR male type connector. It requires an
external 9V - 52V DC phantom power source. Dimensions shall be
18-
1
/2" L. Weight shall be 4 ounces.
GDU150 - The microphone shall be a Bogen Model GDU150. It
shall be a cardioid, dynamic gooseneck microphone with a frequency
response of 100 Hz to 12 kHz and a 500-ohm impedance. The sensi-
tivity shall be -75 dB (+/- 3dB) and the signal-to-noise ratio greater
than 65 dB. It shall have a push-on/push-off talk switch mounted on its
base and a non-glare black finish. The GDU150 shall have an XLR Male
type connector. Dimensions shall be 16-
3
/4" L. Weight shall be 11 oz.
MGN19A - The microphone shall be a Bogen Model MGN19A
dynamic-type, omni-directional microphone. Frequency response shall
be uniform from 50 Hz to 12 kHz, with a presence boost at 1.5 kHz
for natural, intelligible sound. Impedance shall be 500 ohms. A sealed
push-to-talk microswitch shall be mounted on the microphone hous-
ing. The sensitivity shall be -70 dB (+/- 3dB). The microphone shall be
furnished with a 19" black flexible gooseneck and mounting flange and
five feet of rugged synthetic-jacketed 4-conductor, 2-shielded cable.
The microphone shall have a black housing and screen and shall meas-
ure 5.5" long with a maximum diameter of 1.4". Removable set screws
shall secure the front cap to the microphone and the microphone to
the gooseneck. Dimensions shall be 23.66" L. Weight shall be 1.34 lb.
SCU250 - The microphone shall be a Bogen Model SCU250. It shall be
a cardioid, back electret condenser boundary microphone with a fre-
quency response of 20 Hz to 18 kHz and a 250-ohm impedance. The sen-
sitivity shall be -58 dB (+/- 3dB) and the signal-to-noise ratio greater than
65 dB. It shall have a matte black finish and will require an external 9V -
52V DC phantom power source. It shall have a male XLR connector.
Dimensions shall be 2-
3
/4" W x
3
/4" H x 3-
1
/4" D. Weight shall be 11 oz.