Technical Data Sheet

LOCTITE

Frekote PMC™

June-2010

PRODUCT DESCRIPTION

LOCTITE

Frekote PMC™ provides the following product

characteristics:

Technology Cleaner

Appearance Clear liquid

Chemical Type Solvent blend

Odor Solvent

Cure Not applicable

Application Molding

Application

Temperature

20 to 30 °C

LOCTITE

Frekote PMC™ is a special blend of solvents

designed to dissolve and remove wax from polyester molds

without dulling the surface. This product can also be used to

clean epoxy and metal mold surfaces as well as for cleaning

brushes and equipment. LOCTITE

Frekote PMC™ is highly

recommended for preparing polyester mold surfaces prior to

application of Frekote

mold sealers and mold release agents.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Specific Gravity @ 25 °C 0.821 to 0.854

LMS

Flash Point - See SDS

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected as

a sealant for chlorine or other strong oxidizing materials.

For safe handling information on this product, consult the

Safety Data Sheet (SDS).

Directions for use

LOCTITE

Frekote PMC™ should be applied to the mold

surface with a clean lint free cloth.

Wax and other mold residue will immediately begin to

dissolve and should be removed from the surface with a

second clean cloth while it is still dissolved in the

LOCTITE

Frekote PMC™.

3. As the cloth becomes saturated with wax and mold

residue, dispose of it and use a new cloth.

4. Repeat process until composite and other mold residue is

removed.

5. The mold is now ready for use.

6. NOTE: A simple test to assess mold cleanliness is the

use of masking tape. A coated surface will allow easy

release of masking tape, where as a wax free surface will

allow good adhesion of masking tape. This test can also

be used to determine the effectiveness of Frekote

Release Interfaces. A good interface will prevent any

significant degree of tape adhesion.

Loctite Material Specification

LMS

LMS dated November -21, 2005. Test reports for each batch

are available for the indicated properties. LMS test reports

include selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

Storage

The product is classified as flammable and must be stored in

an appropriate manner in compliance with relevant

regulations. Do not store near oxidizing agents or combustible

materials. Store product in the unopened container in a dry

location. Storage information may also be indicated on the

product container labelling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those

previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representive.

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

µm / 25.4 = mil

N x 0.225 = lb

N/mm x 5.71 = lb/in

N/mm² x 145 = psi

MPa x 145 = psi

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Disclaimer

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The product

can have a variety of different applications as well as differing application and

working conditions in your environment that are beyond our control. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product. Any liability in respect of the

For the most direct access to local sales and technical support visit: www.henkel.com/industrial

TDS LOCTITE

Frekote PMC™, June-2010

information in the Technical Data Sheet or any other written or oral

recommendation(s) regarding the concerned product is excluded, except if

otherwise explicitly agreed and except in relation to death or personal injury

caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and

Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Corporation, or Henkel Canada

Corporation, the following disclaimer is applicable:

The data contained herein are furnished for information only and are believed to

be reliable. We cannot assume responsibility for the results obtained by others

over whose methods we have no control. It is the user's responsibility to

determine suitability for the user's purpose of any production methods mentioned

herein and to adopt such precautions as may be advisable for the protection of

property and of persons against any hazards that may be involved in the handling

and use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties of

merchantability or fitness for a particular purpose, arising from sale or use

of Henkel Corporation’s products. Henkel Corporation specifically

disclaims any liability for consequential or incidental damages of any kind,

including lost profits. The discussion herein of various processes or

compositions is not to be interpreted as representation that they are free from

domination of patents owned by others or as a license under any Henkel

Corporation patents that may cover such processes or compositions. We

recommend that each prospective user test his proposed application before

repetitive use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

Trademark usage

Except as otherwise noted, all trademarks in this document are trademarks of

Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark registered

in the U.S. Patent and Trademark Office.

Reference 0.0

For the most direct access to local sales and technical support visit: www.henkel.com/industrial