Technical Data Sheet
LOCTITE ECCOBOND LUX OGR150THTG
June-2016
PRODUCT DESCRIPTION
LOCTITE ECCOBOND LUX OGR150THTG provides the following
product characteristics:
Technology Acrylate
Color Colorless
Cure Ultraviolet (UV) light
Product Benefits ● Non-conductive
● Single component
● Photocurable
● High Tg
● Fast UV cure
● Cures in shadowed areas
● Low temperature cure
Application Assembly
LOCTITE ECCOBOND LUX OGR150THTG photocurable adhesive is
designed for high throughput optoelectronic assembly operations. This
product also contains a secondary thermal cure mechanism for
applications that contain shadowed areas where light is unable to
penetrate. The secondary thermal cure can be done in conventional
box or convection conveyor ovens.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Viscosity, Brookfield SPD#27, 25 °C, mPa·s (cP):
Speed 10 rpm 1,000
Work Life @ 25°C, days
91
Shelf Life @ -5 to +5°C (from date of manufacture), days 183
Flash Point - See SDS
TYPICAL CURING PERFORMANCE
Recommended UV Cure Condition
UV 365 nm with 110 mW/cm²at the bondline
Secondary Thermal Cure Condition
1 hour @ 100°C or
2 hours @ 85°C
The above cure profiles are guideline recommendations. Cure
conditions (time and temperature) may vary based on customers'
experience and their application requirements, as well as customer
curing equipment, oven loading and actual oven temperatures.
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties
Hardness, Shore D 76
Refractive Index:
@ 589 nm 1.5202
@ 830 nm 1.5123
@ 1,320 nm 1.5061
@ 1,550 nm 1.5038
Coefficient of Thermal Expansion :
Below Tg, ppm/°C 61
Above Tg, ppm/°C 157
Glass Transition Temperature (Tg) by DMTA, °C 145
Tensile Modulus, DMTA :
@ -65 °C N/mm² 2,200
(psi) (320,000)
@ 25 °C N/mm² 1,300
(psi) (190,000)
@ 100 °C N/mm² 380
(psi) (54,000)
@ 150 °C N/mm² 75
(psi) (11,000)
Moisture Absorption @ Saturation, wt.% @
85°C/85°RH
1.62
TYPICAL PERFORMANCE OF CURED MATERIAL
Die Shear Strength:
2 X 2 mm Alumina Die to Glass, kg-f/die
Post Cure
@25°C @25ºC with Silane
3.8 19
GENERAL INFORMATION
For safe handling information on this product, consult the Safety
Data Sheet, (SDS).
SHIPMENT AND UNPACKING
1. LOCTITE ECCOBOND LUX OGR150THTG adhesive is packed
and shipped at room temperature.
2. Transfer the syringes from the shipping container to a 0 to 5ºC
freezer without ANY delays. Freeze-thaw voids can form if the
synringes are repeatedly thawed and re-frozen.
DIRECTIONS FOR USE
1. This adhesive is designed to cure upon exposure to UV light. UV
curing is particularly advantageous where a very rapid cure or
curing of a thin section of the assembly is required.
2. Dispense the desired amount of material and place the head into
deposit using downward force to achieve desired bondline.
3. Adhesive must be completely used within the product's
recommended work life.
4. A light source with a minimum output of 500 mW/cm² at 365 nm
wavelength is recommended. Wide ranges of light systems are
available for UV cure, permitting curing of bond profiles in
seconds, coupled with a tack-free surface.
Not for product specifications
The technical data contained herein are intended as reference only.
Please contact your local quality department for assistance and
recommendations on specifications for this product.
TDS LOCTITE ECCOBOND LUX OGR150THTG, June-2016
Storage
Store product in the unopened container in a dry location. Storage
information may be indicated on the product container labeling.
Optimal Storage : -5 to +5 °C
Material removed from containers may be contaminated during use.
Do not return product to the original container. Henkel Corporation
cannot assume responsibility for product which has been contaminated
or stored under conditions other than those previously indicated. If
additional information is required, please contact your local Technical
Service Center or Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
psi x 145 = N/mm²
MPa = N/mm²
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including
the recommendations for use and application of the product are based
on our knowledge and experience of the product as at the date of this
TDS. The product can have a variety of different applications as well as
differing application and working conditions in your environment that
are beyond our control. Henkel is, therefore, not liable for the suitability
of our product for the production processes and conditions in respect
of which you use them, as well as the intended applications and
results. We strongly recommend that you carry out your own prior trials
to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or
any other written or oral recommendation(s) regarding the concerned
product is excluded, except if otherwise explicitly agreed and except in
relation to death or personal injury caused by our negligence and any
liability under any applicable mandatory product liability law.
In case products are delivered by Henkel Belgium NV, Henkel
Electronic Materials NV, Henkel Nederland BV, Henkel
Technologies France SAS and Henkel France SA please
additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal
ground, Henkel’s liability will in no event exceed the amount of the
concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the
following disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including
the recommendations for use and application of the product are based
on our knowledge and experience of the product as at the date of this
TDS. Henkel is, therefore, not liable for the suitability of our product for
the production processes and conditions in respect of which you use
them, as well as the intended applications and results. We strongly
recommend that you carry out your own prior trials to confirm such
suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or
any other written or oral recommendation(s) regarding the concerned
product is excluded, except if otherwise explicitly agreed and except in
relation to death or personal injury caused by our negligence and any
liability under any applicable mandatory product liability law.
In case products are delivered by Henkel Corporation, Resin
Technology Group, Inc., or Henkel Canada, Inc.the following
disclaimer is applicable:
The data contained herein are furnished for information only and are
believed to be reliable. We cannot assume responsibility for the results
obtained by others over whose methods we have no control. It is the
user's responsibility to determine suitability for the user's purpose of
any production methods mentioned herein and to adopt such
precautions as may be advisable for the protection of property and of
persons against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including
warranties of merchantability or fitness for a particular purpose,
arising from sale or use of Henkel Corporation’s products. Henkel
Corporation specifically disclaims any liability for consequential
or incidental damages of any kind, including lost profits. The
discussion herein of various processes or compositions is not to be
interpreted as representation that they are free from domination of
patents owned by others or as a license under any Henkel Corporation
patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application
before repetitive use, using this data as a guide. This product may be
covered by one or more United States or foreign patents or patent
applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are
trademarks of Henkel Corporation in the U.S. and elsewhere. ®
denotes a trademark registered in the U.S. Patent and Trademark
Office.
Reference 1
Americas
+1.888.943.6535
Europe
+32.1457.5611
Asia
+86.21.3898.4800
For the most direct access to local sales and technical support visit: www.henkel.com/electronics