Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Surface Mount
NPCAP
TM
-PXNSeries
・
Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte.
・
High moisture resistance, Bias Humidity: 1,000 hours at 85
℃
, 85%RH
・
Rated voltage range: 2.5 to 16V
dc
, Capacitance range: 56
～
1,200μF
・
Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・
RoHS2 Compliant
・
Halogen Free
・
AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range
2.5 to 16V
dc
Capacitance Tolerance
±
20% (M) (at 20
℃
, 120Hz)
Surge Voltage
Rated voltage
×
1.15 (at 105
℃
)
Leakage Current
Shall not exceed values shown in STANDARD RATINGS. (at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
0.12 max.
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(-25
℃
)/Z(+20
℃
)
≦
1.15
Z(-55
℃
)/Z(+20
℃
)
≦
1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 5,000 hours
at 105
℃
.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Bias Humidity
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to the DC rated voltage at
85
℃
85% RH for 1,000 hours.
Appearance No significant damage
Capacitance change
≦±
30% of the initial value
D.F. (tan
δ
)
≦
200% of the initial specified value
ESR
≦
200% of the initial specified value
Leakage current
≦
The initial specified value
Surge Voltage
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
through a protective resistor(R=1k
Ω
) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆
DIMENSIONS [mm]
0.3max.
W
P
φD
±
0.5
B
±
0.2
C
±
0.2
A
±
0.2
●
Terminal Code : A
L
±
0.3
Size Code
F61
H70
6.3
8
L
5.8
6.7
A
6.6
8.3
B
6.6
8.3
C
7.2
9.0
W
0.5 to 0.8
0.6 to 1.1
P
1.9
E61
5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
3.1
J80
10 7.7 10.3 10.3 11.0 0.6 to 1.1 4.5
φ
D
5
PXN series is a conductive polymer aluminum solid capacitor. All conductive polymer aluminum solid capacitors, including the PXN series
may temporarily exhibit increased leakage current due to heat stress during the reflow soldering process.
However, applying stepped voltage under the category temperature range gradually decreases the increased leakage current to normal
levels. The speed or recovery time that leakage current decreases by self-healing depends on the temperature and voltage: (The closer to
category upper limit temperature and rated voltage, the more rapid the leakage current decrease).
Conductive polymer aluminum solid capacitors do not utilize liquid electrolyte. Therefore it takes a longer period of time to accomplish self-
healing than aluminum electrolytic capacitors that have liquid electrolyte impregnation.
New!
Higher ripple
PXN
PXT
◆
MARKING
N
77C
220
6.3
V
EX) 6.3V220µF
CAT. No. E1001S
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Surface Mount
NPCAP
TM
-PXNSeries
◆
PART NUMBERING SYSTEM
Supplement code
Size code
Capacitance tolerance code
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 10V:100)
Series code
Category
A P X N A R A GM
1 3 42 6 7 8 9 10 13125 18171611 1514
Please refer to "Product code guide (conductive polymer type)"
Capacitance code (ex. 100µF:101, 1,200µ
F:122)
◆
STANDARD RATINGS
WV
(V
dc
)
Cap
(µF)
Size
code
Leakage current
(µA max./after 2min.)
ESR
(m
Ω
max./20
℃
, 100k to 300kHz)
Rated ripple current
(mArms/105
℃
, 100kHz)
Part No.
2.5
330 E61 700 30 2,500 APXN2R5ARA331ME61G
560 F61 700 25 2,800 APXN2R5ARA561MF61G
6.3
220 E61 700 30 2,500 APXN6R3ARA221ME61G
330 F61 700 25 2,800 APXN6R3ARA331MF61G
560 H70 705 20 3,500 APXN6R3ARA561MH70G
1,200 J80 1,510 20 3,500 APXN6R3ARA122MJ80G
10
120 E61 700 35 2,000 APXN100ARA121ME61G
180 F61 700 30 2,500 APXN100ARA181MF61G
270 H70 700 25 3,300 APXN100ARA271MH70G
560 J80 1,120 25 3,400 APXN100ARA561MJ80G
16
56 E61 700 35 2,000 APXN160ARA560ME61G
100 F61 700 30 2,500 APXN160ARA101MF61G
150 H70 700 25 3,300 APXN160ARA151MH70G
330 J80 1,050 25 3,400 APXN160ARA331MJ80G
◆
RATED RIPPLE CURRENT MULTIPLIERS
・
Frequency Multipliers
Frequency(Hz) 120 1k 10k 100k to 300k
SMD type 0.05 0.30 0.70 1.00
PXN series is a conductive polymer aluminum solid capacitor. All conductive polymer aluminum solid capacitors, including the PXN series
may temporarily exhibit increased leakage current due to heat stress during the reflow soldering process.
However, applying stepped voltage under the category temperature range gradually decreases the increased leakage current to normal
levels. The speed or recovery time that leakage current decreases by self-healing depends on the temperature and voltage: (The closer to
category upper limit temperature and rated voltage, the more rapid the leakage current decrease).
Conductive polymer aluminum solid capacitors do not utilize liquid electrolyte. Therefore it takes a longer period of time to accomplish self-
healing than aluminum electrolytic capacitors that have liquid electrolyte impregnation.
New!
CAT. No. E1001S
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS