1. General 一般事項
1.1 Application 適用範囲 This specification covers the requirements for single key switches which have no key top.
(TACT SWITCHES : MECHANICAL CONTACT).
この規格書は、キートップなしのシングルキースイッチ(タクトスイッチ:メカニカルコンタクト)について 適用する。
1.2 Operating temperature range 使用温度範囲: -40 ~ 85 ℃ (normal humidity, normal air pressure 常湿・常圧)
Operating temperature range shall refer to the range where this switch keeps electrical function within such temperatures.
使用温度範囲とはスイッチがON-OFF機能を維持する温度範囲を言う。
1.3 Storage temperature range 保存温度範囲:At Switch level 単品状態 -40 ~ 90 �� (normal humidity, normal air pressure 常湿・常圧)
Switch on Taping テーピング状態 -20 ~ 50 ℃ (humidity 湿度:20~85%)
1.4 Test conditions 試験状態 Unless otherwise specified, the atmospheric conditions for making measurements and tests are as follows.
試験及び測定は特に規定がない限り以下の標準状態のもとで行う。
Normal temperature 常 温: (Temperature 温度 5~35℃)
Normal humidity 常 湿: (Relative humidity 湿度 25~85%)
Normal air pressure 常 圧: (Air pressure 気圧 86~106kPa{860~1060mbar})
If any doubt arise from judgement, tests shall be conducted at the following conditions.
ただし、判定に疑義を生じた場合は以下の基準状態で行う。
Ambient temperature 温 度: 20±2℃
Relative humidity 相対湿度: 60~70%
Air pressure 気 圧: 86~106kPa{860~1060mbar}
Switch shall be mounted on PWB without any indication of switch floating.
スイッチは回路基板から浮かない���うに取り付ける。
2. Appearance, style and dimensions 外観、形状、寸法
2.1 Appearance 外観 There shall be no defects that affect the serviceability of the product.
性能上有害な欠陥があってはならない。
2.2 Style and dimensions 形状、寸法 Refer to the assembly drawings. 製品図による。
3. Type of actuating 動作形式 Tactile feedback タクティールフィードバック
4. Contact arrangement 回路形式 1 poles 1 throws 1 回路 1 接点
(Details of contact arrangement are given in the assembly drawings 回路の詳細は製品図による)
5. Ratings 定格
5.1 Maximum ratings 最大定格 16 V DC 50 mA
5.2 Minimum ratings 最小定格 1 V DC 10μA
6. Electrical specification 電気的性能
Applying a below static load to the center of the stem, measurements shall be made.
スイッチ操作部中央に下記の静荷重を加え,測定する。
(1) Depression 押圧力 : 9 N
(2) Measuring method 測定方法 : 1 kHz small-current contact resistance meter or voltage
drop method at 5VDC 10mA.
1kHz微少電流接触抵抗計,又はDC5V 10mA電圧降下法
Measurements shall be made following the test set forth below:
下記条件で試験を行った後,測定する。
(1) Test voltage 印加電圧: 100 V DC for 1 min.
(2) Applied position 印加場所:Between all terminals. And if there is a metal frame,
between terminals and ground(frame)
端子間,金属フレームがある場合は,端子と金属フレーム間
Measurements shall be made following the test set forth below:
下記条件で試験を行った後,測定する。
(1)Test voltage 印加電圧 : 250 V AC (50~60Hz)
(2)Duration 印加時間 : 1 min
(3)Applied position 印加場所 :Between all terminals. And if there is a metal frame,
between terminals and ground (frame)
端子間、金属フレームがある場合は,端子と金属フレーム間