● Endurnce with ripple current: 105℃ 4000 hours
● Rohs compliance.
◆ SPECIFICATIONS
I≦3√CV
(at 20℃ after 5min.)
10 16 25 35 50 63 80 100 160-250 400-450
20 16 14 12 10 8 8 8 15 12
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to Dcvoltage with the
rated ripple current is applied for 4000 hours at 105℃
Capacitance change
≦±20% of the initial measured v
a
≦ 200% of the initial specified va
l
Leakage Current
≦ the initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing
them for 1000 hours at 105℃ without voltage applied.
Capacitance Change
Leakage Current
●PERMISSIBLE RIPPLE CURRENT MULTIPLIES
⊙Frequency Multipliers
Freq.(Hz) 60(50) 120 300 1K 10K 50K
160~250VDC 0.81 1.00 1.17 1.32 1.45 1.50
315~450VDC 0.77 1.00 1.16 1.3 1.41 1.43
◆ PART NUMBERING SYSTEM
Voltage Range
160 ~ 450V.DC
SL Series
● Non solvent-proof type
Item
Characteristics
Category Temperature Range
-25~+105℃
Dissipation Factor(tanδ)
Rated Voltage(V)
tan δ(max.)
(at 120Hz,20℃)
Capacitance Tolerance
±20%(M) 20℃, 120Hz
Leakage Current
I: Leakage Current (μA) C: Nominal Capacitance (μF) V: Rated Voltage (V)
420V & 450V
Stability at 120Hz Z - 25℃ /Z + 20℃ 48
(at 120Hz,20℃)
Low Temp. Impedance
Rated voltage(V.DC) 160 to 400V
When nominal capacitance is over 1000uF,tan δshall be added 0.02 to the listed value with increase of every 1000 uF.
≦150% of the initial specified value
≦ the initial specified value
tanδ
Aluminum Electrolytic Capacitors
High Temp. Non-Load Test
≦±15% of the initial measured value
High Temp. Load Test
tanδ
SL series
SL series Case Size Table
100 125
35 50 6316
20
25
32
Aluminum Electrolytic Capacitors
80
WV(Vdc)
P
a
r
a
m
e
t
e
r
100
44 63 79
22 25 30 35 22 25 30 35 22 25 30 35 22 25 30 35 22 25 30 35 22 25 30 35 22 25 30 35
25 30 25 30 25
1000
0.25 0.2 0.2 0.2 0.2
Ripple Current (Arms) 120Hz at 10
5
℃ 1.52 1.64 1.64 1.94 1.94
1500
25 30 25 35 (30) 25 40 (35) 25
0.3 0.25 0.25 0.20 0.15 0.20 0.20
0.68 1.68 1.7 1.8 1.8 2.47 2.5
2200
25 30 25 35 30 25 50 (40) (30) 25 45 35
0.35 0.30 0.30 0.25 0.25 0.25 0.20 0.20 0.2 0.2
1.05 2.08 2.08 2.58 2.58 2.58 2.65 2.7 3.15 3.15
3300
25 30 25 35 30 25 45 40 30 25 50 (40) 30 45 35
0.4 0.35 0.35 0.30 0.30 0.30 0.25 0.25 0.25 0.25 0.20 0.20 0.2 0.2
1.65 1.8 1.8 2.65 2.65 2.65 3.3 3.3 3.15 3.15 4.06 4.10 4.06 4.08
4700
25 30 25 35 (30) 25 45 35 30 25 50 35 30 50 40 45
0.5 0.40 0.4 0.35 0.35 0.30 0.30 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25
1.75 2.49 2.45 2.64 2.64 3.09 3.09 3.09 3.09 3.39 3.39 3.39 3.63 3.63 5.12
6800
35 30 35 (30) 25 50 (40) (30) 25 50 35 30 45 40 55 45 50
0.50 0.5 0.40 0.40 0.35 0.35 0.30 0.30 0.30 0.25 0.25 0.25 0.25 0.25
2.40 2.4 2.57 2.57 2.81 2.81 3.86 3.86 3.86 4.34 4.34 4.68 4.68 5.85
10000
45 (35) 25 45 (35) (30) 25 50 (35) 30 45 40 40 35 55 50
0.50 0.50 0.40 0.40 0.35 0.35 0.35 0.35 0.35 0.35 0.30 0.30
3.08 3.08 3.4 3.4 3.55 3.45 4.98 4.98 5.51 5.51 6.08 6.08
15000
45 (35) 30 45 (35) 30 50 40 55
0.50 0.50 0.40 0.40 0.35 0.35 0.30
3.95 3.96 4.1 4.1 5.01 5 5.56
22000
45 35 40 40 45
0.50 0.50 0.40 0.40 0.35
4.71 4.71 5.22 5.22 6.02
33000
40 35 50 45 50
0.50 0.50 0.40 0.40 0.35
5.82 5.82 6.78 6.78 6.95
Case size L in parentheses is not standard. On ordering, please ask us detailed specifications.
100 125
Dissipation Factor
20 32
Case Size L (mm)
P
a
r
a
m
e
t
e
r
Cap (μF)
44 63 79