1
6040
66
Explosion Proof Warning Light/ Signal Light(Telephone Initiated)
SEA-TI/ SEAL-TI/ SEALR-TI/ SEAS-TI
Ex
1. During wiring or maintenance, please completely turn o-• the power of the product. (Fai��lure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a ¿re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If ma���intenance or repair service is required, please contact your local Qlight contact point.
(Failure to follow these instructions may lead to ¿re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to ¿re, electric shock, or p���roduct damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device.
(Failure to follow this may cause damage to property, ¿re, electric shock and loss of life.)
Precaution for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
Safety Precautions for Explosion Proof Products
Please follow the instruction below to ensure safe and correct use of explosion proof products.
1. E��xplosion proof products should be managed according to explosion proof regulations. Do not disassemble, assemble, alter or repair
the product arbitrarily.
2. The temperature rating of the product is the temperature the product will experience at the applied rated voltage and ambient
temperature ��indicated.
3. Use cable glands that satisfy the product’s explosion proof grade and temperature grade.
4. Unused cable entries must be ¿lled with material that meets the explosion proof grade and temperature rating.
5. Before installing the product, please make sure all cautions indicated on the labels, packaging, and operat���ion manual of the product
are fully understood.
6. Installation, maintenance and repair of the product must be performed by experts in the explosion proof ¿eld, or persons who have
received relevant training.
7. For safety, the product should be installed and operated in environments that avoid high temperature and high pressure.
8. Please follow general safety precautions and avoid installing the product in locations that may generate excessive heat.
9. When installing the product in places where chemicals are located, please make sure that the environment does not have two or more
incompatible chemicals mixed. For safety, please read the instruction manual carefully and be mindful of the chemical compositions
where the product is used.
10. This product requires grounding.
11. Please note that special conditions shall be applied if the sign “X” is placed after the certi¿cate numbe���r.
1) For safe use, regular overpressure test must be carried out in accordance with EN 60079-1, clause 15.2.3.
2) For safe use, tempere���d glass must be protected from strong impact
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o-• the power of the p��roduct immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s speci¿cation.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Fa���ilure to follow any of the instructions above may cause malfunction or damage to the product, ¿re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
Thank you for purchasing Qlight’s products. ���Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
2
Zone
de¿nitions(Gas)
Zone 1
High risk gas/vapour
Zone 2
Medium risk gas/vapour
Group
de¿nitions(Gas)
GROUP II A
Acetone, Petrol, Methanol, Propane, Toluene
GROUP II B
Ethylene, City gas
GROUP II C
Hydrogen, Acetylene, Carbon sulphide
Maximum
surface
temperature
of electrical
equipment
T1
450
°C
T2
300°C
T3
200°C
T4
135
°C
T5
100
°C
T6
85
°C
Zone
de¿nitions(Dust)
Zone 21
High risk powder/dust
Zone 22
Medium risk powder/dust
Group
de¿nitions(Dust)
GROUP II A
Ignitible ¿bers/yings(mzore than 0.5mm)
GROUP II B
Non-conductive dusts
GROUP II C
Conductive dusts
Model number
SEA-TI
SEAL-TI
SEALR-TI
SEAS-TI
Range of
operating voltage
DC 12V or 24V
AC 120V or 230V
Ex mark
IECEX - Ex db IIC T6 Gb
ATEX - II2G Ex db IIC T6 Gb
Ambient
operating
temperature
–40°C ≤ Ta ≤ 60°C
��Explosion proof
Zone
Zone1, Zone2
Protection rating
IP66
Model
number
Voltage
Power
consumption
Current
Bulb speci¿cations
Certi¿cate
Weight
Color
Volts/WattsCon¿gurationPart#
SEA-TI
DC12V
25.3W
1.430A 12V15W
G23 15S 17
5.36kg
R-Red
A-Amber
G-Green
B-Blue
DC24V 0.720A 24V15W G23 15S 18
AC120V 0.170A 12V15W G23 15S 17
5.75��kg
AC230V 0.110A 12V15W G23 15S 17
SEAS-TI
DC12V
25.3W
0.690A
200V
-550V
EUB0641
-1A(G)
Utype
48
5.39kg
DC24V 0.380A
AC120V 0.170A
5.35kg
AC230V 0.110A
Model
number
Voltage
Power
consumption
Current Certi¿cate Weight Color
SEAL-TI
DC12V
16.1W
0.140A
4.87kg
R-Red
A-Amber
G-Green
B-Blue
DC24V 0.140A
AC120V 0.110A
5.25kg
AC230V 0.070A
SEALR-TI
DC12V
16.1W
0.210A
5.33kg
DC24V 0.150A
AC120V 0.110A
5.74kg
AC230V 0.070A
■
Telephone lines rated power
• Rated power when telephone lines are not in use: 45VDC - 55VDC
• Rated power when telephone rings : 95VDC - 130VDC(Ring Ring signal sound)
■
General Product Specication
Product Specications
■
Explosion Proof Specications
SEA
-
230
-
R
-
TI
[Model number] [Voltage] [Color] [Telephone Initiated]
| | | |
• SEA
• SEAS
• SEAL
• SEALR
• 12-DC12V
• 24-DC24V
• 120-AC120V
• 230-AC230V
R-Red
A-Amber
G-Green
B-Blue
TI- Telephone Initiated
Ordering Specications