QUICK INSTALLATION GUIDE

SSE-C3632S

SSE-C3632SR

• 32 x 40Gbps/100Gbps QSFP28

• Power Cords – 2

• Rack-mounting kit

(two ears\ two L-brackets\six M4 screws\eight M6 screws)

• Four adhesive foot pads

• RJ-45 to DB-9 serial console cable

flanges or the supplied rails are included in the manual and

summarized below.

The SSE-C3632S/SSE-C3632SR can be mounted in a standard

19-inch equipment rack or on a horizontal surface.

2. Mount the L-bracket in the rack,using the M6 screws provided in the

Rack-Mounting Kit.

3. Mount the device in the rack, using the M6 screws provided in the

Rack-Mounting Kit.

Caution: Due to the weight of the switch, installation should be done

1. Attach the four adhesive feet to the bottom of the first switch.

2. Set the device on a flat surface near an AC power source, making

sure there are at least two inches of space on all sides for proper

airflow.

3. After installation, go to “Connecting to a Power Source”.

Note: For electrical safety purposes, please pay attention to the

following warning notices, printed on the switch unit:

Caution: Disconnect the power cord from all power sources to

completely remove power from the device.

Rack Mounting

This switch can be mounted in a rack using the supplied mounting

flanges or with optional mounting rails.

To rack-mount devices using the supplied brackets (flanges):

1. Attach the ears to the device using the screws provided in

the Rack-Mounting Kit.

Connect the required devices with the appropriate cables.

To connect a device to a power source:

1. Insert the Power Supply Unit (PSU) cable plug directly into the AC

socket of a PSU located at the back of the switch.

SSE-C3632S/SSE-C3632SR switch and use their

instructions for installing their software. Supermicro

recommends Cumulus™Linux® from Cumulus

Networks™, Inc.

• The socket outlet must be near to the unit and easily accessible.

You can only remove power from the unit by disconnecting the

power cord from the outlet.

• This unit operates under SELV (Safety Extra Low Voltage)

conditions according to IEC 60950. The conditions are only

maintained if the equipment to which it is connected also operates

are powered on.

• This product does not contain any serviceable user parts.

• Installation and removal of the unit must be carried out by qualified

personnel only.

• When connecting this device to a power outlet, connect the field

ground lead on the tri-pole power plug to a valid earth ground line

to prevent electrical hazards.

• This switch uses lasers to transmit signals over fiber optic cable.

The lasers are compliant with the requirements of a Class 1

Laser Product and are inherently eye safe in normal operation.

• Use only twisted-pair cables with RJ-45 connectors that conform

to FCC standards.

For more information and safety instruction go to:

http://www.supermicro.com/manuals/network/Layer_2-3_SDN_Switches.pdf

Weight: Net weight: 10.18kg (with 2 PSUs)

LEDs:

System

Fan

SFP+ Port 1: Status (Link/Activity)

Power Supply:

100-127/200-240 VAC, 50/60 Hz,F2B 800W @ 12V/65 A per module

(For SSE-C3632S)

100-127/200-240 VAC, 50/60 Hz,B2F 800W @ 12V/65 A per module

(For SSE-C3632SR)

Power Consumption

: <650 Watts

CE Mark: EN 55022 Class A, EN 55024: 2010, EN 61000-3-2 Class A,

EN 61000-3-3.

Immunity: EN 55024:2010, IEC 61000-4-2/3/4/5/6/8/11

comply with international safety standards.

• Do not connect the unit to an A.C. outlet (power supply) without

an earth (ground) connection.

• The appliance coupler (the connector to the unit and not the wall

plug) must have a configuration for mating with an EN 60320/

IEC 320 appliance inlet.

2. Plug the other end of the cable into a grounded, 3-pin, AC power

source.

Note: For use outside North America, you may need to change

the AC line cord. You must use a line cord that has been

• Console Interface – make sure your console settings are

115200-N-8-1 (baud rate 115,200 bps).

Ports:

32 40Gbps/100Gbps QSFP28 transceiver slots

1 10Gbps SFP+ transceiver slots

Network Interface:

Ports 1~32: 40Gbps/100Gbps QSFP28 Optical

Transceivers:100GBASE-SR4,100GBASE-PSM4

QSFP28 Direct Attach Cables can also be used in ports 1~32