Rev. 1.0a
SAS-826A Backplane
USER'S GUIDE
JSM1
JSM3
JSM2
DESIGNED IN USA
JP46
14
JP13
JP10
1
4
Y2
Y1
F1
F2
F3
U40
1
11
12
22
23
33
34
U19
49
48
33
32
17
16
1
BZ1
C33
C94
C132
C32
C100
+
C285
+
C119
+
C197
+
C198
+
C201
+
C202
+
C3
+
C44
+
C45
+
C5
+
C84
+
C85
C138
C1
C208
C107
C145
C215
C86
C87
C88
C213
C271 C272
CA
D53
CA
D54
C
A
D3
C
A
D36
RT2
JP18
JP35
JP50
R330
R336
R337
R141
R376
R94
R208
R423
R422
R325
R201
R257
R200
R425
R424
R347
R63
R226
R249
R98
R123
R120
R126
R6
R132
JP25
1
JP45
1
JP84
JP37
JP95
JP52
U24
U41
JP69
JP78
RP1
U2
JP26
JP47
U18
BAR CODE
+
B
B
SAS IN #1
SAS IN #2
9072 RST
9071 RST
ACT4
ACT11
ACT10
ACT9
ACT8
ACT3
ACT2
ACT1
ACT7
ACT6
ACT5
ACT0
2-3:I2C
1-2:SGPIO
JP84:MODE
C2-3:55
1-2:50 C
COPEN:45
JP45:OH#2 TEMP
C
C
C2-3:55
1-2:50
OPEN:45
JP25:OH#1 TEMP
ALARM#1
ALARM#2
ACT_IN#8-11
ACT_IN#0-7
UPGRADE#2
UPGRADE#1
SAS IN #3
I2C#3
I2C#2
I2C#1
BUZZER RESET
REV 1.00
SAS826A
SUPER
®
SAS-826A Backplane User’s Guide
ii
Manual Revision 1.0a
Release Date: June 28, 2011
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2011 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America