Technical Data Sheet

LOCTITE

FREKOTE

WOLO-LV™

Known as Frekote WOLO-LV™

June-2015

PRODUCT DESCRIPTION

LOCTITE

FREKOTE

WOLO-LV™ provides the following

product characteristics:

Technology Mold Release

Appearance Clear, colorless

LMS

Chemical Type Solvent Based Polymer

Odor Mild

Cure Room temperature cure

Cured Thermal Stability ≤400 °C

Application Release Coatings

Application Temperature 13 to 41 °C

Specific Benefit ● Reduced VOCs

● High gloss finish

● Easy application

● Fast curing

● Multiple releases

�� Minimal mold build-up

LOCTITE

FREKOTE

WOLO-LV™ is a unique, low VOC

polymer release agent that cures quickly and provides multiple

release of all polyester resins. Applications and use of a

release agent has never been easier, simply wipe on and leave

on to produce a high gloss finish with no need to polish.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Specific Gravity @ 25 °C 0.78 to 0.8

LMS

Flash Point - See SDS

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected as

a sealant for chlorine or other strong oxidizing materials.

For safe handling information on this product, consult the

Safety Data Sheet (SDS).

Mold Preparation

Cleaning:

Mold surfaces must be thoroughly cleaned and dried. All traces

of prior release must be removed. This may be accomplished

by using Frekote

PMC or other suitable cleaner. Frekote

915WB™ or light abrasives can be used for heavy build-up.

Sealing New/Repaired Molds:

Fully cured unused molds should be sealed before use. This

can be accomplished by applying 4 additional coats of

LOCTITE

FREKOTE

WOLO-LV™. Fresh or "production line"

repairs, new fiberglass and epoxy molds should be cured per

manufacturer's instructions, usually a minimum of 2 -3 weeks

at 22°C before starting full-scale production. Occasionally,

green or freshly repaired molds are rushed into service prior to

complete cure causing an increased amount of free styrene on

the mold surface. These areas of the mold surface would be

considered extremely green due to the short cure time and will

require the extra styrene sealing capability of Frekote® Mold

Sealer. Sealing may be accomplished by wiping 2-3 coats of

Frekote

Mold Sealer onto the repaired area(s). Allow full cure

of the appropriate Frekote

mold sealer before you apply the

first coat of LOCTITE

FREKOTE

WOLO-LV™ as outlined in

the directions of use.

Directions for use:

Apply LOCTITE

FREKOTE

WOLO-LV™ with a clean,

lint free, cotton wiping cloth. Wet the cloth with LOCTITE

FREKOTE

WOLO-LV™ until it is damp but not dripping.

Wipe a smooth, wet film over the entire mold surface. Be

sure to avoid drips and puddles. Allow the product to

evaporate. For larger molds, apply LOCTITE

FREKOTE

WOLO-LV™ to the surface one section at a time, being

sure not to miss any areas.

3. Allow a minimum of 5 minutes before applying next coat.

Apply a minimum of four coats in this manner. Dampen

cloth lightly as needed.

4. Allow the final coat to cure for 15 minutes at 20°C.

5. NOTE: If the cloth dries out during your coating process,

use a fresh clean cloth to apply the next coat. This

prevents resin accumulation on the cloth from being

deposited on the mold surface. If streaking occurs,

replace the cloth with a clean dry one and/or make sure

that the cloth is just damp and not soaking wet. Avoid

over-application, as this will cause streaking on the tooling

surface. Streaks or wipe lines can be removed easily by

wiping the mold surface lightly with a dry cloth. Product is

moisture sensitive, keep container tightly closed when not

in use.

NOTE: For maximum number of releases, apply a touch

up coat after the first 2-3 parts are released as a break in

period after the initial application. On deep or high wear

areas, apply an extra 1-2 coats of LOCTITE

FREKOTE

WOLO-LV™. This will help increase the slip even further

in these high drag areas.

Mold Touch up

Abrasion will gradually cause wear and parts will begin to

adhere to the mold surface if a continuous release film is not

maintained. It's best to always touch-up the mold at the first

sign of diminished release, before release becomes difficult.

Simply touch-up the entire mold or apply spot touch-ups to high

TDS LOCTITE

FREKOTE

WOLO-LV™, June-2015

wear areas following steps 1-3 under directions for use. Only 1

coat is usually required for touch-up. Typically, 15 minutes cure

time is required prior to resumption of molding.

Loctite Material Specification

LMS

LMS dated January-18, 2007. Test reports for each batch are

available for the indicated properties. LMS test reports include

selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

Storage

The product is classified as flammable and must be stored in

an appropriate manner in compliance with relevant

regulations. Do not store near oxidizing agents or combustible

materials. Store product in the unopened container in a dry

location. Storage information may also be indicated on the

product container labelling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those

previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representive.

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

µm / 25.4 = mil

N x 0.225 = lb

N/mm x 5.71 = lb/in

N/mm² x 145 = psi

MPa x 145 = psi

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Note:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The product

can have a variety of different applications as well as differing application and

working conditions in your environment that are beyond our control. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and

Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is

applicable:

The data contained herein are furnished for information only and are believed to

be reliable. We cannot assume responsibility for the results obtained by others

over whose methods we have no control. It is the user's responsibility to

determine suitability for the user's purpose of any production methods mentioned

herein and to adopt such precautions as may be advisable for the protection of

property and of persons against any hazards that may be involved in the handling

and use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties of

merchantability or fitness for a particular purpose, arising from sale or use

of Henkel Corporation’s products. Henkel Corporation specifically

disclaims any liability for consequential or incidental damages of any kind,

including lost profits. The discussion herein of various processes or

compositions is not to be interpreted as representation that they are free from

domination of patents owned by others or as a license under any Henkel

Corporation patents that may cover such processes or compositions. We

recommend that each prospective user test his proposed application before

repetitive use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

Trademark usage

Except as otherwise noted, all trademarks in this document are trademarks of

Henkel Corporation in the U.S. and elsewhere.

denotes a trademark

registered in the U.S. Patent and Trademark Office.

Reference 0.1

Americas

+860.571.5100

Europe

+49.89.320800.1800

Asia

+86.21.2891.8863

For the most direct access to local sales and technical support visit www.henkel.com/industrial