Technical Data Sheet

LOCTITE

ECCOBOND EO1061

November -2018

PRODUCT DESCRIPTION

LOCTITE

ECCOBOND EO1061 provides the following product

characteristics:

Technology Epoxy

Appearance Black

Product Benefits ● High performance

● Medium flow

Filler Weight, % 61.3

Components One-component

Cure Heat cure

Application Encapsulation

Typical Applications Chip-on-board and Low profile divices

LOCTITE

ECCOBOND EO1061 is designed to pass 1,000 hours of

temperature/humidity/bias testing and thermal cycling up to 125°C.

Exceptional viscosity stability at 25°C provides easier control of shot

size using conventional time/pressure dispensing equipment.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Viscosity, Brookfield - RVF, 25 °C, mPa·s (cP):

Spindle 6, speed 2 rpm 50,000

Spindle 6, speed 20 rpm 32,500

Specific Gravity @ 25 °C 1.78

Pot Life @ 25ºC, 200 grams mass, days 25

Gel Time @ 121ºC, minutes 13

Shelf Life - Refer to package label

Flash Point - See SDS

TYPICAL CURING PERFORMANCE

Recommended Cure Schedule

3 hours @ 140°C

Designed to be used with packages which are affected

by higher levels of stress. This cure will give optimum

properties.

Curing below 125°C is not recommended.

The above cure profile is a guideline recommendation. These cure

conditions (time and temperature) may vary based on customers'

experience and specific application requirements, as well as

customer curing equipment, oven loading and actual oven

temperatures.

TYPICAL PROPERTIES OF CURED MATERIAL

Physical Properties

Coefficient of Thermal Expansion, ppm/°C:

Below Tg (40 to 120°C) 40

Glass Transition Temperature(Tg), °C 125

Extractable Ionic Content, :

Chloride (Cl-) 70

Sodium (Na+) 20

Potassium (K+) 20

Linear Shrinkage, % 1.07

Flexural strength N/mm² 64.8

(psi) (9,400)

Electrical Properties

Dielectric Constant / Dissipation Factor, IEC 60250:

@ 25 °C:

1kHz 4.97 / 0.0083

10-kHz 4.92 / 0.109

100-kHz 4.83 / 0.132

Volume Resistivity, IEC 60093, Ω·cm 1.9×10

Surface Resistivity, IEC 60093, Ω 2.0×10

GENERAL INFORMATION

For safe handling information on this product, consult the

Safety Data Sheet, (SDS).

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected as a

sealant for chlorine or other strong oxidizing materials.

THAWING:

1. Allow container to reach room temperature before use.

Directions for use

LOCTITE

ECCOBOND EO1061 is not designed with

thixotropic properties. A physical barrier, such as plastic case

potting ring is required to control flow.

Storage

Store product in the unopened container in a dry location. Storage

information may be indicated on the product container labeling.

Optimal Storage : -40 °C

Material removed from containers may be contaminated during use.

Do not return product to the original container. Henkel Corporation

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those previously

indicated. If additional information is required, please contact your

local Henkel Representative.

Not for product specifications

The technical data contained herein are intended as reference only.

Please contact your local quality department for assistance and

recommendations on specifications for this product.

TDS LOCTITE

ECCOBOND EO1061, November -2018

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

N x 0.225 = lb/F

N/mm x 5.71 = lb/in

psi x 145 = N/mm²

MPa = N/mm²

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Disclaimer

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The

product can have a variety of different applications as well as differing

application and working conditions in your environment that are beyond our

control. Henkel is, therefore, not liable for the suitability of our product for the

production processes and conditions in respect of which you use them, as well

as the intended applications and results. We strongly recommend that you

carry out your own prior trials to confirm such suitability of our product. Any

liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is

excluded, except if otherwise explicitly agreed and except in relation to death

or personal injury caused by our negligence and any liability under any

applicable mandatory product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS

and Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the

following disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel

is, therefore, not liable for the suitability of our product for the production

processes and conditions in respect of which you use them, as well as the

intended applications and results. We strongly recommend that you carry out

your own prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any

other written or oral recommendation(s) regarding the concerned product is

excluded, except if otherwise explicitly agreed and except in relation to death

or personal injury caused by our negligence and any liability under any

applicable mandatory product liability law.

In case products are delivered by Henkel Corporation, or Henkel Canada

Corporation, the following disclaimer is applicable:

The data contained herein are furnished for information only and are believed

to be reliable. We cannot assume responsibility for the results obtained by

others over whose methods we have no control. It is the user's responsibility

to determine suitability for the user's purpose of any production methods

mentioned herein and to adopt such precautions as may be advisable for the

protection of property and of persons against any hazards that may be

involved in the handling and use thereof. In light of the foregoing, Henkel

Corporation specifically disclaims all warranties expressed or implied,

including warranties of merchantability or fitness for a particular

purpose, arising from sale or use of Henkel Corporation’s products.

Henkel Corporation specifically disclaims any liability for consequential

or incidental damages of any kind, including lost profits. The discussion

herein of various processes or compositions is not to be interpreted as

representation that they are free from domination of patents owned by others

or as a license under any Henkel Corporation patents that may cover such

processes or compositions. We recommend that each prospective user test

his proposed application before repetitive use, using this data as a guide. This

product may be covered by one or more United States or foreign patents or

patent applications.

Trademark usage

Except as otherwise noted, all trademarks in this document are trademarks of

Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark

registered in the U.S. Patent and Trademark Office.

Reference 2

For the most direct access to local sales and technical support visit: https://www.henkel-adhesives.com/