Technical Data Sheet
LOCTITE ECCOBOND EO1016
December-2014
PRODUCT DESCRIPTION
LOCTITE ECCOBOND EO1016 provides the following
product characteristics:
Technology Epoxy
Appearance (cured) Black
Product Benefits • Excellent shelf stability
• Fast curing
• flame-out
Components One-component
Cure Heat cure
Application Encapsulant
Typical Applications IC's, transistors and similar
semiconductors
Flammability Rating Passes UL 94 V0
LOCTITE ECCOBOND EO1016 is an epoxy encapsulant
intended for applications requiring excellent handling
properties. The cured material survives severe thermal shock
and offers continuous service to 177 °C. It is particularly suited
for use on transistors and similar semiconductors, can be used
for encapsulation of watch ICs.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Viscosity, Brookfield - RVF, 25 °C, mPa·s (cP):
Spindle 6, speed 2 rpm 62,000
Spindle 6, speed 20 rpm 58,000
Thixotropic Index 1.1
Specific Gravity @ 25ºC 1.56
Shelf Life:
@ 4ºC, days
365
@ -40ºC, days
365
Gel Time @ 121ºC, minutes 4.5
Pot life @ 25°C, days 91
Flash Point - See SDS
TYPICAL CURING PERFORMANCE
Recommended Cure Schedule
20 minutes @ 150°C
Alternate Cure Schedule
24 hours @ 93°C
The above cure profile is a guideline recommendation. Cure conditions
(time and temperature) may vary based on customers' experience and
their application requirements, as well as customer curing equipment,
oven loading and actual oven temperatures.
Differential Scanning Calorimetry
Initial Temperature, °C 122
Peak Temperature, °C 138
Energy to break point, Joules 0.414
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties :
Coefficient of Linear Thermal Expansion, ppm/ºC:
Below Tg 46
Above Tg 140
Glass Transition Temperature, °C 126
Coefficient of Thermal Conductivity, W/(m-K) 0.39
Extractable Ionic Content, , ppm:
Chloride (Cl-) 1.2
Tensile Strength N/mm² 55.17
(psi) (8,000)
Flexural Modulus N/mm² 5,880
(psi) (852,600)
Flexural strength N/mm² 100
(psi) (14,500)
Adhesion psi
Cohesive
Al-Al Tensile shear
3,660
Elongation, % 1.8
Shore Hardness , Durometer D ≥86
Linear Shrinkage, 10 grams, % 1.7
Moisture Absorption, %:
24 hours immersion @ 25°C 0.06
24 hours immersion @ 50°C 0.23
Electrical Properties:
Dielectric Constant / Dissipation Factor, IEC 60250:
@ 25 °C:
1kHz 4.3 / 0.0084
Arc Resistance, ASTM D495, 180
Volume Resistivity, IEC 60093, 6×10
15
Surface Resistivity, IEC 60093, 1×10
16
GENERAL INFORMATION
For safe handling information on this product, consult the
Safety Data Sheet, (SDS).
Not for product specifications
The technical data contained herein are intended as reference
only. Please contact your local quality department for
assistance and recommendations on specifications for this
product.
TDS LOCTITE ECCOBOND EO1016, December-2014
Directions for use
1. Mix thoroughly each time it is used.
2. Heating to 32 to 43°C will lower viscosity and aid in
mixing and pouring.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage : -40 °C
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
psi x 145 = N/mm²
MPa = N/mm²
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS)
including the recommendations for use and application of the
product are based on our knowledge and experience of the
product as at the date of this TDS. The product can have a
variety of different applications as well as differing application
and working conditions in your environment that are beyond
our control. Henkel is, therefore, not liable for the suitability of
our product for the production processes and conditions in
respect of which you use them, as well as the intended
applications and results. We strongly recommend that you
carry out your own prior trials to confirm such suitability of our
product.
Any liability in respect of the information in the Technical Data
Sheet or any other written or oral recommendation(s) regarding
the concerned product is excluded, except if otherwise
explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any
applicable mandatory product liability law.
In case products are delivered by Henkel Belgium NV,
Henkel Electronic Materials NV, Henkel Nederland BV,
Henkel Technologies France SAS and Henkel France SA
please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever
legal ground, Henkel’s liability will in no event exceed the
amount of the concerned delivery.
In case products are delivered by Henkel Colombiana,
S.A.S. the following disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS)
including the recommendations for use and application of the
product are based on our knowledge and experience of the
product as at the date of this TDS. Henkel is, therefore, not
liable for the suitability of our product for the production
processes and conditions in respect of which you use them, as
well as the intended applications and results. We strongly
recommend that you carry out your own prior trials to confirm
such suitability of our product.
Any liability in respect of the information in the Technical Data
Sheet or any other written or oral recommendation(s) regarding
the concerned product is excluded, except if otherwise
explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any
applicable mandatory product liability law.
In case products are delivered by Henkel Corporation,
Resin Technology Group, Inc., or Henkel Canada, Inc.the
following disclaimer is applicable:
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions. We recommend that each
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.
Trademark usage
Except as otherwise noted, all trademarks in this document
are trademarks of Henkel Corporation in the U.S. and
elsewhere. ® denotes a trademark registered in the U.S.
Patent and Trademark Office.
Reference 1
Americas
+1.888.943.6535
Europe
+32.1457.5611
Asia
+86.21.3898.4800
For the most direct access to local sales and technical support visit: www.henkel.com/electronics