Technical Data Sheet
LOCTITE ECCOBOND DS 3318LV
November-2016
PRODUCT DESCRIPTION
LOCTITE ECCOBOND DS 3318LV provides the following
product characteristics:
Technology Acrylic
Appearance Light yellow, transparent liquid
Components One-component
Product Benefits • Fast cure
• Low energy cure
• Good moisture resistance
• High flexibility
Cure Ultraviolet (UV)/ visible light, UV LED
Application Coating and Sealant
Typical Package
Application
LCD module assembly
LOCTITE ECCOBOND DS 3318LV is suitable for a wide
variety of coating applications that require strict humidity
reliability performance, such as ITO/COG overcoat in LCD
module assembly.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Viscosity @ 25 °C, mPa∙s (cP) 968
Specific Gravity 0.97
Shelf Life @ 25°C, months 12
Flash Point - See SDS
TYPICAL CURING PERFORMANCE
Recommended UV Cure
Ultraviolet (UV), Visible light or UV LED
Light Source and Condition:
High pressure mercury lamp
Irradiance, mW/cm² 100
Tack Free Time
Time required to achieve tack-free surface, seconds 3
Depth of Cure
LOCTITE ECCOBOND DS 3318LV can be cured by
irradiation with ultraviolet and visible light as well as LED-UV
light with single wavelength distribution of sufficient intensity.
Cure rate and depth of cure depend on the intensity,
spectral distribution of the light source, exposure time and
light transmittance of the substrate through which the light
must pass.
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties :
Glass Transition Temperature, DMA, °C 64
Water Permeability, gm/mil/100 in²/day:
24 hours, 50ºC, 100% RH 21
Extractable Ionic Content, , ppm:
Chloride (Cl-) 7.0
Sodium (Na+) 1.0
Modulus , Fusion, irradiated 4 times:
N/mm² 504
(psi) (73,099)
Electrical Properties:
Volume Resistivity , ohms-cm 4.94×10
16
Miscellaneous:
Tensile Strength, at break, sample cured with 2,000 mJ/cm²
energy:
N/mm² 13.3
(psi) (1,929)
TDS LOCTITE ECCOBOND DS 3318LV, November-2016
GENERAL INFORMATION
For safe handling information on this product, consult the Safety
Data Sheet, (SDS).
This product is not recommended for use in pure oxygen and/or
oxygen rich systems and should not be selected as a sealant for
chlorine or other strong oxidizing materials.
Not for product specifications
The technical data contained herein are intended as reference only.
Please contact your local quality department for assistance and
recommendations on specifications for this product.
STORAGE:
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage : 25 °C
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
psi x 145 = N/mm²
MPa = N/mm²
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Corporation, Resin Technology
Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
Trademark usage: [Except as otherwise noted] All trademarks in this document
are trademarks and/or registered trademarks of Henkel and its affiliates in the
U.S. and elsewhere.
Reference 1
Americas
+1.888.943.6535
Europe
+32.1457.5611
Asia
+86.21.3898.4800
For the most direct access to local sales and technical support visit: www.henkel.com/electronics