Ver.1.06
CPS-MCS341G-DS1-130 1
CONPROSYS Series
CPU Module
3G Model
CPS-MCS341G-DS1-130
* Specifications, color and design of the products are subject to change
without notice.
This product is a M2M controller with isolated digital input and output,
RS-232C, LAN interface, Ethernet Hub, and a 3G network communication
module, which can be operated in Japan.
As you desire, add the configurable type modules of our CONPROSYS
series.
All the processes from development to operation can be performed on a
web browser. The functions such as Web monitoring of I/O information,
alarm processing by I/O information, task divergence enable you to
create a Cloud System at low cost and in a short time.
* The contents in this document are subject to change without notice.
* Visit the CONTEC website to check the latest details in the document.
* The information in the data sheets is as of December, 2018.
Hardware Features
Comply with Japan National Standards of 3G network
Following the regulation by the Radio Act of Japan, this product transmits
the collected data to the cloud server through 3G communication
network.
* Please contact us for detailed information.
Add configurable modules
This product allows you to install modules from a wide variety of types to
suit the needs of the user.
* Up to 16 modules can be set and the total current consumption should
be less than 3.3A.
No base board required
As the product requires no base board for installation, it helps add
modules easily and smoothly.
Installed modules can be removed from any set positions on DIN rail.
Compact design
Compact design, 44.7(W)×94.7(D)×124.8 (H), features flexibility in
installation.
Adaptable to a temperature range between -20 and +60°C
The product is capable of operating in the temperature between -20 and
+ 60°C. It can be installed in the various environments.
Ethernet Hub function within
Use the product as Ethernet Hub so that you can connect devices in the
daisy-chain.
A powerful running platform without fan
The product contains the ARM® Cortex®-A8 processor (600MHz) and
the DDR3 512MB system memory.
Decrease damages by bus isolation and surge protection. (digital
input/output)
Electrical isolation between the digital input/output and CPU can block
electrical noise flow. Moreover, the surge protection elements are
adopted
Opto-coupler Isolation Input and semiconductor relay output
The product has the switchable four channels of opto-coupler isolation
input (compatible with current sink output) and semiconductor relay
output. It is usable for external switch inputting or LED lighting.
Max. 115,200bps RS-232C Serial Communication
The Product has one RS-232C-standard serial port. Baud rates from 300
to 115,200 bps can be set.
Installation easy with two pieces of terminal support and DIN rail
You can install and remove a terminal connector without a screwdriver so
that it can shorten the time of the replacement. As the product can be
mounted on a DIN rail, removing and replacing are easy as well.
Equipped with LED for an operation check
The product has LED for an operation check, which helps you visually
confirm the communication status of each interface.
No electrolytic capacitor battery
No electrolytic capacitor is used. The Contec is creating the product with
a longer life.
Software Features
Measurement and upload
This product measures data with an external sensor and uploads them to
the Cloud server.
Web monitoring
The product contains a Web server (Java applet). Even with the PC
located remotely, I/O information can be monitored and updated
through a Web browser
On the monitoring screen, the standard GUI parts (graphic, slider, button,
etc.) can be freely arranged.
All operations including monitoring layout, making relations with I/O
information, can be achieved through a Web browser.
Web task script
By combining icons such as arithmetic operations, conditional branching,
data outputting, you can set up the executions or its processes like
drawing them in the flowchart. All operations can be completed through
a Web browser.
Message communication function
With the RS-232C or the Ethernet device (TCP/UDP), up to 10 links can be
set to send or receive messages.
Message communication can be accomplished from Web task script.
Ver.1.06
CPS-MCS341G-DS1-130 2
Specifications
Function specifications
Item
CPS-MCS341G-DS1-130
CPU
ARM Cortex-A8 600MHz
Memory
On Board 512MB DDR3 SDRAM
OM
On-Board 64MB NOR Flash for OS
LAN
Transmission standard
10BASE-T/100BASE-TX
The number of channels
2
Connector
RJ-45 Connector
LED
Speed (Yellow), Link/Act (Green)
USB
Transmission standard
USB2.0 standard follow
The number of channels
1
Connector
TYPE-A
SD card slot
Standard
SD standard follow
Connector
SD memory card slot
LED
Read/Write (Green)
RS-232C
Baud Rate
300bps - 115.2kbps
Data length
5, 6, 7, 8 bit 1, 1.5, 2 stopbit
Parity check
Even, Odd, Non-parity
Isolation/Resistance
Non-isolated
The number of channels
1
Connector
9-pin D-SUB connector (Male)
LED
Transmission (Green), Reception (Green)
Digital input and
Output
Input type
Opto-coupler isolation input (Compatible with current sink
output) (negative logic) *1
Input isolation
Opto-coupler isolation
Input voltage resistance
1000V
The number of input signal
channels
4
Open-circuit impedance
10kΩ or more
Short-circuit impedance
500Ω or less
Response time (digital
input)
Within 200μsec
Interrupt (digital input)
4 interrupt input signals are arranged into a single output of
interrupt signal.
An interrupt is generated at the falling edge (HIGH-to-LOW
transition) or rising edge (LOW-to-HIGH transition). (setting
can be done by software)
Output type
Semiconductor relay output
Output isolation
Semiconductor relay isolation
Output voltage resistance
1000V
The number of output
signal channels
4 *usable as digital input or digital output
Maximum output
voltage/current
13.2V/100mA
Response time
Within 2msec
ON resistance
8Ω or less (at 25 °C)
OFF leakage current
4μA or less (at 25 °C)
Surge protection element
Interactive TVS Diode
Stand off voltage : ±30V, Peak pulse power : 400W(1ms)
LED
DIO0-DIO3 (Green)
Connector
2 pieces 3.81mm pitch 6-pin Terminal
(N.C., DIO3, DIO2, DIO1, DIO0, MCOM)
Applicable wire
AWG28 - 16
Stack Bus
The maximum number of
stack buses
16 *2
LED
Power (Green)/Status 1 (Green)/Status 2 (Red) /Error(Red)
Switch
Power SW, Rotary SW, DIP SW
RTC
RTC built-in (battery within)
Power supply *3
Rated input voltage
24VDC
Input voltage range
21.6 - 26.4VDC
Power consumption
Controller alone: 24V 0.3A (Max.)
With module(s): 24V 3.6A (Max.)
Connector
2-piece 3.5mm pitch 3-pin terminal (V+, V-, FG)
Applicable wire
AWG20 - 16
Surge protection element
V+ - V-, V- - FG
Interactive TVS diode
Stand off voltage : ±30V, Peak pulse power : 400W(1msec)
Physical dimensions (mm)
44.7(W)×94.7(D)×124.8(H) ( No projection included)
Weight
300g
Item
CPS-MCS341G-DS1-130
Installation method
Quick mounting on the 35mm DIN rail
OS
Linux kernel 3.2
*1 Data 0 corresponds to High level and Data 1 corresponds to Low level.
*2 The total current consumption of the devices should be less than 3.3A
*3 Use power cable within 3meters.
Wireless Specifications
Item
CPS-MCS341G-DS1-130
Support SIM
MVNO SIM
SIM slot
Standard SIM
Communication method
3G (UMTS)
Wireless frequency
(domestic support exclusively)
Band1(2100MHz), Band2(1900MHz), Band5(850MHz),
Band6(800MHz), Band8(900MHz), Band19(800MHz)
Communication
speed
Maximum 384kBit/s
Maximum 384kBit/s
Installation Environment Requirements
Item
CPS-MCS341G-DS1-130
Operating ambient temperature
-20 - +60°C *4
Operating ambient humidity
10 - 90%RH (No condensation)
Non-operating ambient
temperature
-20 - +60°C
Non-operating ambient humidity
10 - 90%RH (No condensation)
Floating dust particles
Not to be excessive
Corrosive gases
None
Line-noise
resistance
Line noise
AC Line/±2kV *5
Signal Line /±1kV(IEC61000-4-4 Level 3, EN61000-4-4 Level 3)
Static
electricity
resistance
Touch /±4kV(IEC61000-4-2 Level 2, EN61000-4-2 Level 2)
Air /±8kV(IEC61000-4-2 Level 3, EN61000-4-2 Level 3)
Vibration
resistance
Sweep
resistance
10 - 57Hz *6 /semi-amplitude vibration 0.15mm, 57 - 150Hz/2.0G
40minutes each in X, Y, and Z directions (JIS C60068-2-6-compliant,
IEC60068-2-6-compliant)
Shock resistance
15G half-sine shock for 11ms in X, Y, and Z directions
(JIS C 60068-2-27 -compliant, IEC 60068-2-27 -compliant)
Grounding
Class D grounding (previous class 3 grounding), SG-FG/ non-conduction
Standard
VCCI Class A, TELEC
*4 If you use the USB with bus power, operate the product at between -20 and +55°C.
*5 When you use the optional power product.
*6 When you use an optional power product: 10 - 55Hz (See the manual of optional power product for details)
Packing List
Product [CPS-MCS341G-DS1-130] …1
End Cover…1(attached to the product)
Product Guide … 1
Warranty Certificate …1
Cautions for setting the SIM card…1
Serial Number Label …1
3-pin Connector…1
6-pin Connector…1
Antenna…1
※ Use the supplied plastic DIN rail when connecting this product and a module on a desk top for system
development or validation. If you use the supplied plastic DIN rail in the field, it cannot be covered by warranty.
Therefore, when you set the product and module in the field, use the commercially available DIN rail.