Technical Data Sheet
LOCTITE ECCOBOND LUX 3042M
October-2016
PRODUCT DESCRIPTION
LOCTITE ECCOBOND LUX 3042M provides the following product
characteristics:
Technology Acrylate
Color Pale yellow
Cure Ultraviolet (UV) light, Visible light and
Heat cure
Product Benefits ● One component
● Dual cure system
● Non-conductive
● Good adhesion on various
substrates
Application Assembly
LOCTITE ECCOBOND LUX 3042M dual cure adhesive is designed for
use in the assembly of temperature sensitive electronic components.
This product is formulated to initially cure when exposed to UV light,
followed with a secondary thermal cure to achieve maximum
performance.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Viscosity , TA Rheometer, mPa∙s (cP):
Cone 20 mm, Angle 2º @ Shear rate 20 s
-1
85,000
Thixotropic Index (0.1/1 rpm) 1.2
Specific Gravity, g/cm³ 1.1
Flash Point - See SDS
TYPICAL CURING PERFORMANCE
Recommended UV Cure
Light Source:
High Pressure Mercury Lamp:
UV Wavelength, nm 300 to 500
Light Intensity, mW/cm² 100
Exposure Time, seconds 5
Secondary Thermal Cure Condition
30 minutes @ 120°C
The above cure profiles are guideline recommendations. Cure
conditions (time and temperature) may vary based on customers'
experience and their application requirements, as well as customer
curing equipment, oven loading and actual oven temperatures.
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties
Hardness, Shore D 85
Coefficient of Thermal Expansion :
Below Tg, ppm/°C 87
Above Tg, ppm/°C 174
Glass Transition Temperature (Tg) by TMA, °C 114
Modulus N/mm² 1,700
(psi) (247,000)
TYPICAL PERFORMANCE OF CURED MATERIAL
Sample cured 30 minutes @ 120°C.
Lap Shear Strength , FR4 / FR4, 0.075 mm thickness,
N/mm²
>8
GENERAL INFORMATION
For safe handling information on this product, consult the Safety
Data Sheet, (SDS).
DIRECTIONS FOR USE
1. To ensure the long term performance of the bonded assembly,
complete cleaning of the substrates
should be performed to remove contamination such as oxide
layers, moistures, dust, salts and oils which
can cause poor adhesion or corrosion in a bonded part.
2. Apply adhesive to all surfaces to be bonded and join together.
STORAGE:
Store product in the unopened container in a dry location. Storage
information may be indicated on the product container labeling.
Optimal Storage : -40 °C
Material removed from containers may be contaminated during use.
Do not return product to the original container. Henkel Corporation
cannot assume responsibility for product which has been contaminated
or stored under conditions other than those previously indicated. If
additional information is required, please contact your local Technical
Service Center or Customer Service Representative.
Not for product specifications
The technical data contained herein are intended as reference only.
Please contact your local quality department for assistance and
recommendations on specifications for this product.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
psi x 145 = N/mm²
MPa = N/mm²
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
TDS LOCTITE ECCOBOND LUX 3042M, October-2016
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Corporation, Resin Technology
Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks of
Henkel Corporation in the U.S. and elsewhere.
®
denotes a trademark
registered in the U.S. Patent and Trademark Office.
Reference 1
Americas
+1.888.943.6535
Europe
+32.1457.5611
Asia
+86.21.3898.4800
For the most direct access to local sales and technical support visit: www.henkel.com/electronics