Technical Data Sheet

LOCTITE

FREKOTE FMS™

Known as FMS™

August-2014

PRODUCT DESCRIPTION

LOCTITE

FREKOTE FMS™ provides the following product

characteristics:

Technology Mold Release

Appearance Clear, colorless

LMS

Chemical Type Solvent Based Polymer

Odor Hydrocarbon

Cure Room temperature cure

Application Mold Sealer

Application

Temperature

13 to 35 °C

Specific Benefit ● High gloss finish

● Easy application

● Fast curing

● Eliminates

Porosity/Microporosity

● Seals "green" molds and

repaired areas

LOCTITE

FREKOTE FMS™ is formulated specifically as a

sealer for fiberglass reinforced polyester, epoxy and other

composite molds commonly used in the fiberglass molding

industry. LOCTITE

FREKOTE FMS™ must be used when

using green, or new, molds with microporosity and other slight

surface imperfections.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Specific Gravity @ 25°C 0.757 to 0.771

LMS

Flash Point - See SDS

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected as

a sealant for chlorine or other strong oxidizing materials.

For safe handling information on this product, consult the

Safety Data Sheet (SDS).

Mold Preparation

Cleaning:

Mold surfaces must be thoroughly cleaned and dried. All traces

of prior release must be removed. This may be accomplished

by using Loctite

Frekote

PMC or other suitable cleaner.

Loctite

Frekote

915WB™ or light abrasives can be used for

heavy build-up.

Full curing of green/new molds is highly recommended to

ensure optimal performance of the sealer.

Directions for use:

Apply LOCTITE

FREKOTE FMS™ with a clean, lint free,

cotton wiping cloth. Wet the cloth with LOCTITE

FREKOTE FMS™ until it is damp but not dripping.

Wipe a smooth, wet film over the entire mold surface. For

larger molds, apply LOCTITE

FREKOTE FMS™ to the

surface one section at a time starting at one end and

working towards the other. Using a clean cloth, wipe off

the area that was just treated to obtain a smooth thin wet

layer.

3. Allow a minimum of 15 minutes before applying next coat.

New molds require 1 to 2 coats of sealer.

4. NOTE: Changes in temperature will affect solvent dry

time. At temperatures below 18°C, waiting time between

wiping on and drying off can be slightly longer than 20

seconds. At higher then normal temperatures (greater

then 35°C) the wait time is significantly reduced and can

be as quick as 1 to 2 seconds. In these conditions it is

also advisable to reduce your wipe area to eliminate

streaking due to the increased solvent evaporation and

polymer cure times. A general guideline is to wait until the

edges of the wiped area begins to creep inwards

indicating the evaporation has just begun. Wipe from the

outside and slowly work your way towards the center.

Light hand pressure is all that is needed. No hard rubbing

required. change cloth frequently to ensure proper drying

of the mold. On small molds, allow up to 15 minutes

between coats. If one coat takes more than 15 minutes,

simply go back to starting point and begin to apply next

coat. .

5. Allow the final coat to cure for 20 minutes at 20°C.

Loctite Material Specification

LMS

LMS dated February -07, 2007. Test reports for each batch

are available for the indicated properties. LMS test reports

include selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

TDS LOCTITE

FREKOTE FMS™, August-2014

Storage

The product is classified as flammable and must be stored in

an appropriate manner in compliance with relevant

regulations. Do not store near oxidizing agents or combustible

materials. Store product in the unopened container in a dry

location. Storage information may also be indicated on the

product container labelling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those

previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representive.

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

µm / 25.4 = mil

N x 0.225 = lb

N/mm x 5.71 = lb/in

N/mm² x 145 = psi

MPa x 145 = psi

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Note:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The product

can have a variety of different applications as well as differing application and

working conditions in your environment that are beyond our control. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and

Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is

applicable:

The data contained herein are furnished for information only and are believed to

be reliable. We cannot assume responsibility for the results obtained by others

over whose methods we have no control. It is the user's responsibility to

determine suitability for the user's purpose of any production methods mentioned

herein and to adopt such precautions as may be advisable for the protection of

property and of persons against any hazards that may be involved in the handling

and use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties of

merchantability or fitness for a particular purpose, arising from sale or use

of Henkel Corporation’s products. Henkel Corporation specifically

disclaims any liability for consequential or incidental damages of any kind,

including lost profits. The discussion herein of various processes or

compositions is not to be interpreted as representation that they are free from

domination of patents owned by others or as a license under any Henkel

Corporation patents that may cover such processes or compositions. We

recommend that each prospective user test his proposed application before

repetitive use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

Trademark usage: [Except as otherwise noted] All trademarks in this document

are trademarks and/or registered trademarks of Henkel and its affiliates in the

U.S. and elsewhere.

Reference 0.0

Americas

+860.571.5100

Europe

+49.89.320800.1800

Asia

+86.21.2891.8863

For the most direct access to local sales and technical support visit www.henkel.com/industrial