ATtiny806/1606
tinyAVR
®
0-series
Introduction
The ATtiny806/1606 are members of the tinyAVR
®
0-series of microcontrollers, using the AVR
®
processor with hardware multiplier, running at up to 20 MHz, with 8/16 KB Flash, 512/1024 bytes of
SRAM, and 128/256 bytes of EEPROM in a 20-pin package. The tinyAVR
®
0-series uses the latest
technologies with a flexible, low-power architecture including Event System and SleepWalking, accurate
analog features, and Core Independent Peripherals.
Attention: Automotive products are documented in separate data sheets.
Features
• CPU:
– AVR
®
CPU
– Running at up to 20 MHz
– Single-cycle I/O access
– Two-level interrupt controller
– Two-cycle hardware multiplier
• Memories:
– 8/16 KB In-system self-programmable Flash memory
– 128/256B EEPROM
– 512/1024B SRAM
– Write/erase endurance:
• Flash: 10,000 cycles
• EEPROM: 100,000 cycles
– Data retention: 40 years at 55°C
• System:
– Power-on Reset (POR)
– Brown-out Detector (BOD)
– Clock options:
• 16/20 MHz low-power internal RC oscillator
• 32.768 kHz Ultra Low-Power (ULP) internal RC oscillator
• External clock input
– Single-pin Unified Program and Debug Interface (UPDI)
© 2019 Microchip Technology Inc.
Preliminary Datasheet
DS40002029B-page 1
– Three sleep modes:
• Idle with all peripherals running for immediate wake-up
• Standby:
– Configurable operation of selected peripherals
– SleepWalking peripherals
• Power-Down with full data retention
• Peripherals:
– One 16-bit Timer/Counter type A (TCA) with dedicated period register and three compare
channels
– One 16-bit Timer/Counter type B (TCB) with input capture
– One 16-bit Real-Time Counter (RTC) running from internal RC oscillator
– Watchdog Timer (WDT) with Window mode, with a separate on-chip oscillator
– One USART with fractional baud rate generator, auto-baud, and start-of-frame detection
– Master/slave Serial Peripheral Interface (SPI)
– One Two-Wire Interface (TWI) with dual address match
• Philips I
2
C compatible
• Standard mode (Sm, 100 kHz)
• Fast mode (Fm, 400 kHz)
• Fast mode plus (Fm+, 1 MHz)
– One Analog Comparator (AC) with a low propagation delay
– One 10-bit 150 ksps Analog-to-Digital Converter (ADC)
– Multiple voltage references (VREF):
• 0.55V
• 1.1V
• 1.5V
• 2.5V
• 4.3V
– Event System (EVSYS) for CPU independent and predictable inter-peripheral signaling
– Configurable Custom Logic (CCL) with two programmable look-up tables
– Automated CRC memory scan (CRCSCAN)
– External interrupt on all general purpose pins
• I/O and Packages:
– 18 Programmable I/O lines
– 20-pin VQFN 3x3 mm and SOIC300
• Temperature Ranges:
– -40°C to 105°C
– -40°C to 125°C
• Speed Grades:
– 0-5 MHz @ 1.8V – 5.5V
– 0-10 MHz @ 2.7V – 5.5V
– 0-20 MHz @ 4.5V – 5.5V
ATtiny806/1606
© 2019 Microchip Technology Inc.
Preliminary Datasheet
DS40002029B-page 2