PESD2463U250
1. Electrical Specification
1-1 Test condition
Varistor voltage In = 1 mA DC
Leakage current
Vdc = 24 V DC
Maximum clamping voltage
Ic = 1 A
Rated peak single pulse transient current
8 / 20 ㎲ waveform, +/- each 1 time induce
Capacitance 10/1000 ㎲ waveform
Insulation resistance after reflow soldering f = 1MHz, Vrms = 0.5 V
Reflow soldering condition
Soldering paste : Tamura (Japan) RMA-20-21L
Stencil : SUS, 120 ㎛ thickness
Pad size : 0.8 (Width) x 0.9 (Length)
0.8 (Distance between pads)
Soldering profile : 260±5 ℃, 5 sec.
1-2 Electrical specification
Maximum allowable continuous DC voltage 24
V
trigger voltage / Varistor voltage / breakdown voltage 125
V
Maximum clamping voltage 200
V
Maximum
Rated peak single pulse transient current
1
A
Maximum
Nonlinearity coefficient
＞ 12
Leakage current at continuous DC voltage
＜ 0.1
㎂
Response time
＜ 1.0
ns
Varistor voltage temperature coefficient
＜ 0.05
%/℃
Capacitance measured at 1MHz
2.5
pF
Typical
Capacitance tolerance
40
%
Insulation resistance after reflow soldering on PCB
＞ 10
MΩ
Operating ambient temperature -55 to +85
℃
Storage temperature -55 to +125
℃
Rev : www.leiditech.com
01.06.2018
1/5
1-3 Reliability testing procedures
Reliability
parameter
Test
Test methods and remarks
Test requirement
Pulse current
capability
Imax
8/20 ㎲
IEC 1051-1, Test 4.5.
10 pulses in the same direction at 2
pulses per minute at maximum peak
current
dVn/Vn≤ 10%
no visible damage
Electrostatic
discharge
capability
ESD
C=150 pF,
R=330Ω
IEC 1000-4-2
Each 10 times in positive/negative
direction in 10 sec at 8KV contact
discharge (Level 4)
dVn/Vn≤ 10%
no visible damage
Environmenta
l reliability
Thermal shock
IEC 68-2-14
Condition for 1 cycle
Step 1 : Min. –40℃, 30±3 min.
Step 2 : Max. +125℃, 30±3 min.
Number of cycles: 30 times
dVn/Vn≤ 5%
no visible damage
Low temperature
IEC 68-2-1
Place the chip at -40±5℃ for 1000±
12hrs. Remove and place for 24±2hrs at
room temp. condition, then measure
dVn/Vn≤ 5%
no visible damage
High temperature
IEC 68-2-2
Place the chip at 125±5℃ for 1000±
24hrs. Remove and place for 24±2hrs at
room temp. condition, then measure
dVn/Vn≤ 5%
no visible damage
Heat resistance
IEC 68-2-3
Apply the rated voltage for 1000±48hrs at
85±3℃. Remove and place for 24±2hrs
at room temp. condition, then measure
dVn/Vn≤ 5%
no visible damage
Humidity
resistance
IEC 68-2-30
Place the chip at 40±2℃ and 90 to 95%
humidity for 1000±24hrs. Remove and
place for 24±2hrs at room temp.
condition, then measure
dVn/Vn≤ 10%
no visible damage
Pressure cooker
test
Place the chip at 2 atm, 120℃, 85%RH
for 60 hrs. Remove and place for 24±
2hrs at room temp. condition, then
measure
dVn/Vn≤ 10%
no visible damage
PESD2463U250
Rev : www.leiditech.com
01.06.2018
2/5