1 / 10
Document No.
PRS
-
2490
Confidential C
I
PEX Inc. QKE
DFFDE06
08 REV.9
MHF
®
I Connector (Plug: 2.00 Type)
Part No. Plug: 20767-001R-20 Receptacle: 20279-001E-**
Product Specification
Qualification Test Report No. TR-18041
0 S18391 June 26, 2018 M.Nomoto K.Motomura K.Yotsutani
Rev. ECN Date Prepared by Checked by Approved by
MHF I
Connector
(Plug: 2.00 Type)
Product Specification
Document No.
PRS
-
2490
2 / 10
Confidential C
1. 適応範囲/Scope
本規格は、AWG#26 同軸ケーブルの基板対ワイヤーコネクタである MHF I Connector の性能と試験条件について規定する。
This Product Specification defines the test conditions and the performances of the MHF I Connector, a
wire-to-board connector for AWG#26 coaxial cable.
2. 製品名称及び製品型番/Product Name and Parts No.
2.1 製品名称/Product Name
MHF I Connector
2.2 製品型番/Parts No.
Plug: 20767-001R-20
Receptacle: 20279-001E-**
3. 定格/Rating
3.1 適応ケーブル/Applicable Cable
(1) ���成/Description
中心導体: AWG#26(7/0.16), 銀メッキ軟銅線
誘電体: 外径 1.50 (±0.10) mm, フッ素樹脂
外部導体: 標準外径 1.70mm, 16/7/0.05, 錫メッキ軟銅線
ジャケット: 外径 2.00 (±0.10) mm, フッ素樹脂
(2) 仕様/Requirements
特性インピーダンス: 50±5Ω (TDR)
絶縁抵抗: 1,000MΩ・km 以上
耐電圧: AC 500V・1分間にて絶縁破壊の無い事
(1) Description
Inner conductor: AWG#26 (7/0.16), Silver plating annealed copper wire
Dielectric core: diameter 1.50 (±0.10) mm, Fluor-plastics
Outer conductor: nominal diameter 1.70mm, 16/7/0.05, Tin plating annealed copper wire
Jacket: diameter 2.00 (±0.10) mm, Fluor-plastics
(2) Requirements
Characteristic impedance : 50±5Ω by TDR method
Insulation resistance : 1,000 MΩ・km MIN.
Dielectric withstand voltage: no breakdown at AC 500V for 1 minutes.
3.2 使用条件/Operating Conditions
電圧/Voltage: 60V AC (per a contact)
公称特性インピーダンス/Nominal characteristic impedance: 5
VSWR: Plug 1.3 Max at 0.1∼3GHz , 1.5 Max at 3∼6GHz
Receptacle 1.3 Max at 0.1∼3GHz. 1.4 Max at 3∼6GHz
使用温度/Operating temperature: 233K~363K(-40℃~90℃)
(通電による温度上昇含む/Containing temperature rise by current)
3.3 保管条件/Storage Conditions
保管温度/Storage temperature: 248~333K(-25℃~60℃)
保管湿度/Storage humidity: 85% max. (結露無きこと/Non-condensing)
4. 試験及び性能/Test and Performance
試験条件/Test Condition
特に指定のない限り、測定と試験は、MIL-STD-202G に基づき以下の条件で行う。
This initial test is equal to it’s at shipping condition and unless otherwise specified, all tests and
measurements shall be performed under the following conditions in accordance with MIL-STD-202 G.
温度/Temperature… 288K~308K(15℃~35℃)
相対湿度/Relative humidity… 45~75%R.H.