S100L
-
BZ
-
220
-
R
[Model
number]
[Buzzer] [Voltage] [Color]
| | | |
• S100L
• S125L
• (Blank)
- No buzzer type
• BZ
- Built-in buzzer
type
• 12/24
- DC12V~24V
• 110 - AC110V
• 220 - AC220V
R-Red
A-Amber
G-Green
B-Blue
1
S100L/ S125L
LED Steady/ Flashing Signal Light
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the
product that would void the warranty.
1. During wiring or maintenance, please completely turn o the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
Ordering Specications Product Specications
Please scan the QR code
for more
detailed product information.
www.qlight.com
• Protection rating : IP44
• Ambient operating temperature : -30°C to +50°C
Model
number
Voltage Current
Certicates
Weight
Color
S100L
DC12V~24V Max.0.185A 0.26kg
R-Red
A-Amber
G-Green
B-Blue
AC110V 0.045A
0.45kg
AC220V 0.025A
S125L
DC12V~24V Max.0.300A 0.33kg
AC110V 0.060A
0.51kg
AC220V 0.030A
※
CE compliant : DC12V/24V
90
dB
5020
44
2
• External power line - UL1015 AWG18(0.75sq) × 2C 400mm
• This product can be wired regardless of polarity.
• For built-in buzzer type, there is a shared supply line for the buzzer and lighting element.
S125LS100L
158
103
48
12
Ø119
Ø10 CABLE ENTRY
PCD 85
360˚/3-M5 BOLT
152
9246
12
Ø101
Ø10 CABLE ENTRY
PCD 60
360˚/3-M4 BOLT
DC AC
3-Ø5 HOLES
Min.Ø5 CABLE ENTRY
Min.Ø5 CABLE ENTRY
3-Ø6 HOLES
PCD 85
PCD 60
S100L S125L
S100L S125L
Wiring Instructions
Dimensions
(Units : mm)
Red
Black
Power
Fuse
White
Black
Power
Fuse
Parts Denition/ Installation/ Light Function Selection/ Mounting Hole Specications
■
Parts Denition/ Installation
■
Light Function Selection
■
Mounting Hole Specications
• Please refer to the chart below to use light function selection
switch located inside the product.
•
Default function is set at steady LED. Select the desired function
for your application during installation.
▶
L : Steady
▶
LF : Flashing
• Machine holes on the mounting surface referring to the
diagram below.
• First, remove the ange nuts from bolts and place the
product through the mounting surface holes.
• Fasten the ange nuts on the opposite side of the
mounting surface until the product is tightened securely.
Reector
(Heat resistant ABS)
Lens(AS)
LED unit
Housing(ABS)
Flange nut
Rubber spacer
Flat washer