Qualification Test Report
501-137013-2
Rev. A1
©2012 TE Connectivity (Shanghai) Co. Ltd
Shanghai P.R.C.
All International Rights Reserved
Information is TE Connectivity Confidential &
Proprietary.
Do Not Reproduce or Distribute
Page 1 of 4
H16B/H24B Hood & Housing with cover
1. INTRODUCTION
1.1 Purpose
This document provides the qualification summery of TE Connectivity Hood & Housing of HDC connector.
1.2 Scope
This specification covers the electrical, mechanical, and environmental performance of H16B/H24B Hood
& Housings with cover. Testing was performed at the Shanghai Electrical Components Test Laboratory.
1.3 Conclusion
Based on the test results, all meet the requirements according to TE Connectivity Design Objectives
108-137013.
1.4 Product Description
Name
H16B-AD-BO
H16B-TSBHS-PG21
H24B-AD-BO
H24B-TSBHS-PG21
1.5 Qualification Test Sequence
Test and Examination
Test Group
A
B
C
D
E
F
Test Sequence
1)
Visual and dimensional examination
1,3
1,3
1,7
1,7
1,4
1,3
Mechanical strength impact
2
Mechanical Operation (Durability)
2
Vibration, Random
2
Shock
3
Cold
3
3
Dry Heat
4
4
Rapid Change of temperature (Temperature Cycle)
5
5
Salt Mist Cyclic Test
2
Degree of protection IP6X
2,6
Degree of protection IPX5
2,6
* Notes:
1) Numbers indicate the sequence in which the tests are performed.
Qualification Test Report 501-137013-2
Page 2 of 4
2. TEST PROCEDURE
General
No.
Description
Test procedure according
Requirements
2.1
Visual and
dimension
examination
Visual and dimensional examination
IEC 60512-1-1/-2, Test 1a and 1b
Meets requirements of product drawing
Mechanical
2.2
Mechanical
strength
impact
Dropping height:
- 750mm for specimens of mass≤250g
- 500mm for specimens of mass>250g
Dropping cycles:8
positions in 45°step, one cycles per position
IEC 60512-7-2 Test 7b
No damage likely to impair function
2.3
Mechanical
Operation
(Durability)
Shall operate to open /close the locking
system by means of
A) a device simulating normal use
B) manual open/close 200 Max. cycle per
hour
1) 100 operation cycles
2) No damage likely to impair normal use
2.4
Vibration,
Random
Frequency:5~150Hz
Per EN 61373, Category 1, Class B
(IEC60068-2-6 Test Fc)
No damage likely to impair function No
discontinuities greater than t>1μs
2.5
Shock
Acceleration:50m/s2
Duration:30ms
Total 18 shocks(three positive and three
negative in each of the three orthogonal axes)
Per EN 61373
No damage likely to impair function No
discontinuities greater than t>1μs
Environmental
2.6
Cold
Subject mated specimen to
-40℃ Duration time:16h, Test Ab
Per IEC 60512-11-10 Test 11j
(IEC 60068-2-1)
No damage likely to impair function
2.7
Dry Heat
Subject mated specimen to
+125℃ Duration time:168h Test Bb
Per IEC 60512-11-9 Test 11i
(IEC 60068-2-2)
No damage likely to impair function
2.8
Rapid Change
of temperature
(Temperature
Cycle)
Subject mated specimen to
Ta=-40±2℃ to Tb=+125±2℃,
duration: ta=1h, tb=1h,,
100 cycles
IEC 60512-11-4 Test 11d
(IEC 60068-2-14 Test Na)
No damage likely to impair function
2.9
Salt Mist
Cyclic Test
Mated connector and expose to the following
salt mist condition. Atmosphere: salt spray
from a 5±1% concentration solution;
PH value: 6.5~7.2
Per IEC60068-2-52, Severity 1,
1 Cycle
No damage likely to impair function