DESIGN OBJECTIVES 10Jan07
Design
Objectives
108-2277
Rev O3
Right Angle AMC B+ Card Edge Connector
©2007 Tyco Electronics Corporation
Harrisburg, PA
All International Rights Reserved.
* Trademark
| Indicates change
For latest revision, vis it our website at www.tycoelectronics.com \documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
1 of 7
LOC B
DESIGN OBJECTIVES
The product described in this document has not been fully tested to ensure conforma nce to the requirements outlined below. Therefore Tyco
Electronics makes no re presentation or warra nty, express or implied, that the product will comply with the se requireme nts. Further, Tyco
Electronics may change these requirements based on the results of additional testing and evaluation. Contact Tyco Electronics Engineering for
further d eta i l s.
1. SCOPE
1.1. Content
This specific ati on c overs perfor manc e, t ests and qual it y r equirements f or the Ty c o E lectronics Ri ght
Angl e A M C B + Card E dge Connec tor.
1.2. Qualification
When tests are perfor med on the subjec t product li ne, proc edur es specified in Figur e 1 shal l be used.
Al l inspections shall be performed usi ng the appli c able inspection plan and produc t drawing.
2. APPLICABLE DOCUMENT S
The following document s for m a par t of this specification to the ext ent specified her ein. Unless
otherwise specified, the lat est editi on of the document appl ies. In the event of confli c t bet ween the
requi r ements of thi s specification and the pr oduc t drawing, the produc t drawing shall take prec edenc e.
In t he event of confl ic t between the requirements of thi s specification and the r eferenced documents,
this specific ati on shal l take prec edenc e.
2.1. Tyc o E lec tronics Document s
109 Series: T est S pec ificat ions as indicat ed in Fi gur e 1
109-197: T est Speci ficat ion (AMP T est Speci ficat ions vs EIA and IE C Test Methods)
114- : A pplication Specificati on
501- : Quali fication Test Repor t (Right A ngle A M C B + Card Edge Connec tor)
2.2. Industry S tandards
EIA - 364: Electrical Connec tor/ S oc k et Test P r oc edur es Inc luding Envi r onmental Classificati ons
GR-1217- CORE: Gener ic Requirements For Separable E lectrical Connectors Used In
Telecommunicat ions Hardware
IEC 60512: Electromec hanic al Component s For E lec tronic E quipment; B asi c Testi ng P r oc edur es
and Measuring M ethods Part 1: Gener al
3. REQUIREMENTS
3.1. Design and Construction
Product shall be of the design, c onstr uc tion and physic al dimensi ons specified on t he applicable
product dr awing.
3.2. Mater ials
Mater ials used in the c onstr uc tion of thi s product shall be as specified on the appl ic able produc t
drawing.
DESIGN OBJECTIVES 10Jan07
108-2277
Rev O3 2 of 7
3.3. Ratings
Vol tage: 1.7 to 1.9 volts DC
Current : Signal appli c ation onl y
Temper ature: - 10 to 70 C
Hum idit y : 10 t o 90%, non-condensi ng
3.4. Perform anc e and Test Descri pti on
Product is desi gned to meet the elect r ical, mechanical and envi r onmental perfor mance requi r ements
specified in Figure 1. Unless other wise specified, all t ests shall be perform ed at ambient envi r onmental
condi tions.
3.5. Test Requirements and Procedur es Summar y
Test Descript ion Requir ement Procedur e
Init ial examinat ion of product. Meets requirements of product
drawing.
IEC 60512- 2, T est 3A .
Vi sual and dimensi onal ( C of C)
inspect ion per pr oduc t drawing.
(Connect or interface, i nterface
dimensi ons of plug-in car d, and
creepage and clear anc e distances).
Final examinat ion of pr oduc t. Meets visual r equirements. No
defect that would impair normal
operation.
IEC 60512- 2, T est 3A .
Vi sual inspect ion.
ELECTRICAL
Low lev el termination resistance. 60 milliohms maximum initial.
R 15 milliohms maximum.
EIA-364-23.
Subj ec t speci mens to 100
milliamperes maximum and 20
millivolts maximum open circ uit
volt age.
Insulation resistanc e. 100 m egohms mi nimum between
different ial pair conduc tors
m utuall y and between ground;
between general pur pose
conduct or s mut ually and between
ground; and between power
conduct or s mut ually and between
ground.
10 m egohms aft er humidit y .
IEC 60512- 2, T est 3A , Test
Vol tage 80 volts rm s, M ethod B.
Vol tage proof. One minut e hold with no
breakdown or flashover .
IEC 60512- 2, T est 4A , Met hod B .
Mated plug- in car ds.
Test vol tage 80 volt s rms. between
different ial pair conduc tors
m utuall y and gr ound; bet ween
general pur pose conductors
m utuall y and gr ound; and bet ween
power conductors mut ually and
ground.
Figure 1 ( c onti nued)