Product Data Sheet
BISCO® HT-6135 is a part of the
performance grade solid silicone series.
High tear strength and extremely tight
thickness tolerances of these materials
offer added benefits for sealing.
PHYSICAL
The information contained in this Data Sheet is intended to assist you in designing with Rogers’ Elastomeric Material Solutions.
It is not intended to and does not create any warranties, express or implied, including any warranty of merchantability or fitness
for a particular purpose or that the results shown in this Data Sheet will be achieved by a user for a particular purpose. The user
should determine the suitability of Rogers BISCO products for each application. The Rogers logo, BISCO logo, and BISCO are
trademarks of Rogers Corporation or one of its subsidiaries. © 2002, 2003, 2004, 2008, 2019, 2020 Rogers Corporation.
All rights reserved. 0320-PDF • Publication #180-092
PROPERTY
TEST METHOD
BISCO® HT-6135
Color
Visual
Cream
Durometer, Shore A
ASTM D2240
35 ± 5
Thickness, mm (inches)
Internal
Compression Set, %
ASTM D395
150°C (302°F) / 70 hrs / 25%
< 25
Specific Gravity, (g/cc)
ASTM D412
ASTM D412
1.22
580
>
5
.52
(
>
8
00)
TYPICAL VALUE*
0.250 - 1.59
(0.010 - 0.063)
Internal
Tensile Strength, MPa (psi)
Tear Resistance, ppi
ASTM D624
116
SPECIFICATION**
33
Dielectric Strength, Volts/mil
ASTM D149
Dielectric Constant, 1 kHz
ASTM D150
Dissipation Factor, 1 kHz
Dry Arc Resistance, Seconds
ASTM D495
PROPERTY
TEST METHOD
TYPICAL VALUE* SPECIFICATION**
ELECTRIC
381
2.95
0.001
145
---
---
---
ASTM D495
ASTM D257
Volume Resistivity, Ohm-cm
---
10^14
---
---
---
---
---
---
---
Elongation, %
---
Specification values in bold are tested on a batch basis.Sp
Further industry specifications tested in tables below.
The information contained in this Data Sheet is intended to assist you in designing with Rogers’ Elastomeric Material Solutions.
It is not intended to and does not create any warranties, express or implied, including any warranty of merchantability or
fitness for a particular purpose or that the results shown in this Data Sheet will be achieved by a user for a particular purpose.
The user should determine the suitability of Rogers BISCO products for each application. The Rogers logo, BISCO logo, and
BISCO are trademarks of Rogers Corporation or one of its subsidiaries. © 2002, 2003, 2004, 2008, 2019, 2020 Rogers Corporation.
All rights reserved. 0320-PDF • Publication #180-092
Standard
Thickness Tolerances
NOMINAL THICKNESS
TOLERANCE
mm (inches)
mm
(inches)
0.254
(0.01
0)
± 0.051
(± 0.002)
0.
508
(
0.020)
± 0.102
(± 0.004)
0.787
(0.031
)
± 0.076
(± 0.003
)
1.600
(0.063)
± 0.152
(± 0.006)
V
ALUE ADDED OFFERINGS
• Adhesive (PSA) lamination on ≥ 0.031"
• Slit material/tapes
Notes:
Tape (PSA) Width Tolerances
NOMINAL WIDTH
TOLERANCE
mm (inches)
mm
(inches)
+ 25.4/- 0
(+ 1/- 0)
>
660 - 914
(> 26 - 36)
Temperature Range, °
C
(°F)
Internal
Thermal Conductivity, W/m °K
ASTM D518
Low Temperature Brittleness
-55
to +200
(-67 to +392)
ASTM D2137
PROPERTY
TEST METHOD
TYPICAL VALUE*
SPECIFICATION**
THERMAL
---
---
--
-
0.31
Pass
-62°C (-80°F) / 3 min
*Typical Value- Value is based on historical data. Please note the frequency of testing varies.
**Specification- Applies to physical properties only, which are based on Rogers' internal benchmark and standard BISCO specification values.
Additional industry specifications are available as well. All other properties are based on industry standard guidelines.