Product Data Sheet
BISCO® HT-6210 extra soft silicone material
is part of the performance grade solid
silicone series. The material's low Shore OO
durometer, high tear strength, and
extremely tight thickness tolerances offer
added benefits for sealing.
PHYSICAL
The information contained in this Data Sheet is intended to assist you in designing with Rogers’ Elastomeric Material Solutions.
It is not intended to and does not create any warranties, express or implied, including any warranty of merchantability or fitness
for a particular purpose or that the results shown in this Data Sheet will be achieved by a user for a particular purpose. The user
should determine the suitability of Rogers BISCO products for each application. The Rogers logo, BISCO logo, and BISCO are
trademarks of Rogers Corporation or one of its subsidiaries. © 2002, 2003, 2004, 2018, 2019, 2020 Rogers Corporation.
All rights reserved. 0320-PDF • Publication #180-090
PROPERTY
TEST METHOD
BISCO® HT-6210
Color
Visual
Gray
Durometer, Shore OO
ASTM D2240
62 ± 4
Thickness, mm (inches)
Internal
Compression Set, %
ASTM D395
150°C (302°F) / 22 hrs / 50%
< 25
Specific Gravity, (g/cc)
ASTM D412
ASTM D412
1.07
> 400
3.3
(
48
0
)
TYPICAL VALUE*
0.250 - 3.18
(0.010 - 0.125)
Internal
Tensile Strength, MPa (psi)
Tear Resistance, ppi
ASTM D624
> 20
SPECIFICATION**
61
Dielectric Strength, Volts/mil
ASTM D149
Dielectric Constant, 1 kHz
ASTM D150
Dissipation Factor, 1 kHz
Dry Arc Resistance, Seconds
ASTM D495
PROPERTY
TEST METHOD
TYPICAL VALUE*
SPECIFICATION**
ELECTRIC
372
2.76
0.003
122
---
---
---
ASTM D495
ASTM D257
Volume Resistivity, Ohm-cm
---
10^14
• Provides low closure force
• Bridges the gap between foams and high durometer solids
Features & Benefits:
> 1.4
(> 200)
565
Elongation, %
---
---
---
---
---
---
Specification values in bold are tested on a batch basis.Sp
Further industry specifications tested in tables below.
The information contained in this Data Sheet is intended to assist you in designing with Rogers’ Elastomeric Material Solutions.
It is not intended to and does not create any warranties, express or implied, including any warranty of merchantability or fitness
for a particular purpose or that the results shown in this Data Sheet will be achieved by a user for a particular purpose. The user
should determine the suitability of Rogers BISCO products for each application. The Rogers logo, BISCO logo, and BISCO are
trademarks of Rogers Corporation or one of its subsidiaries. © 2002, 2003, 2004, 2018, 2019 , 2020 Rogers Corporation.
All rights reserved. 0320-PDF • Publication #180-090
Standard
Thickness Tolerances
NOMINAL THICKNESS
TOLERANCE
mm (inches)
mm
(inches)
0.254
(0.01
0)
± 0.051
(± 0.002)
0.508
(0.020)
± 0.102
(± 0.004)
0.787
(0.031
)
+ 0.076/- 0.051
(+ 0.003/- 0.002)
1.600
(0.063)
± 0.152
(± 0.006)
Notes:
Width Tolerances
NOMINAL WIDTH
TOLERANCE
mm (inches)
mm
(inches)
+ 25.4/- 0
(+ 1/- 0)
Temperature Range, °
C
(°F)
Internal
Thermal Conductivity, W/m ºK
ASTM D518
Low Temperature Brittleness
-
55 to +200
(-67 to +392)
ASTM D2137
PROPERTY
TEST METHOD
TYPICAL VALUE* SPECIFICATION**
THERMAL
---
---
--
-
0.19
Pass
-62°C (-80°F) / 3 min
(0.125)
(
±
0.0
08)
3.175
± 0.203
914
(36)
*Typical Value- Value is based on historical data. Please note the frequency of testing varies.
**Specification- Applies to physical properties only, which are based on Rogers' internal benchmark and standard BISCO specification values.
Additional industry specifications are available as well. All other properties are based on industry standard guidelines.
All metric conversions are approximate. Reference US customary units for official values and tolerances.