© TT Electronics plc
General Note
All data sheets are subject to change without noce.
TT Electronics | Power Partners, Inc
43 Broad Street Suite B206, Hudson, MA 01749, USA. t: +1 (978) 567-9600
SL-xxx-xxx ISS.6 22/07/2020 Page: 1
Descripon:
The PMP90 series of AC/DC switching power supplies are for 60-90 was of connuous output power. They are enclosed in
a 94V-0 rated polyphenylene-oxide case with an IEC320/C14 or IEC320/C18 inlet to mate with interchangeable cord for
world-wide use. All models meet EN55011 and FCC class B emission limits, and are designed for medical applicaons.
Features:
• Low safety ground leakage current
• Wide input range 90 to 264 VAC
• Oponal output connectors
• 100% burn-in
• Overvoltage protecon
• Over-temperature protecon
• Overcurrent protecon
• Compliant with CEC and Energy Star Eciency level IV requirements
(except models
PMP90-10, PMP90-10-1 and PMP90-11)
• No load power consumpon less than 0.5W
• Average acve eciency greater than 85%
• Compliant with RoHS requirements
• IEC 60601-1-2 4th Edion EMC Compliant
Model
1
Output
Average Acve
Eciency (typical)
@115/230 Vac
Class-I Class-II V1
Min.
Current
Max.
Current
Tol.
Ripple &
Noise
2
Max. Power
PMP90-10 PMP90F-10 5V 0A 12A ±5% 100mV 60W 78/79%
PMP90-10-1 PMP90F-10-1 6V 0A 10A ±5% 100mV 60W 78/79%
PMP90-11 PMP90F-11 9V 0A 7.78A ±5% 100mV 70W 81/82%
PMP90-12 PMP90F-12 12V 0A 6.67A ±5% 120mV 80W 86/85%
PMP90-12-1 PMP90F-12-1 13.5V 0A 6.3A ±5% 135mV 85W 86/85%
PMP90-13 PMP90F-13 15V 0A 5.67A ±5% 150mV 85W 86/85%
PMP90-13-1 PMP90F-13-1 18V 0A 5A ±5% 180mV 90W 86/85%
PMP90-13-2 PMP90F-13-2 19V 0A 4.74A ±5% 190mV 90W 86/86%
PMP90-14 PMP90F-14 24V 0A 3.75A ±5% 240mV 90W 87/86%
PMP90-16 PMP90F-16 30V 0A 3A ±5% 300mV 90W 87/86%
PMP90-18 PMP90F-18 48V 0A 1.87A ±5% 480mV 90W 88/87%
NOTES:
1. Class I models are equipped with IEC320/C14 inlet, and class II models with IEC320/C18 inlet.
2. Ripple and noise is maximum peak to peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and
output load ranges, and with a 10 μF tantalum capacitor in parallel with a 0.1 μF ceramic capacitor across the output.
© TT Electronics plc
General Note
All data sheets are subject to change without noce.
TT Electronics | Power Partners, Inc
43 Broad Street Suite B206, Hudson, MA 01749, USA. t: +1 (978) 567-9600
SL-xxx-xxx ISS.6 22/07/2020 Page: 2
Specicaons
Safety Standards & EMC Specicaons
Safety Standard Approvals
UL ES 60601-1, CSA C22.2 No. 60601-1 File No. E178020
TÜV EN 60601-1
EMI Standard EN55011/EN55022, FCC, and VCCI Class B (radiated and conducted)
EMC Performance
EN61000-3-2: Harmonic distoron, Class A and D
EN61000-3-3: Line icker
EN61000-4-2: ESD, ±15 KV air and ± 8KV contact
EN61000-4-3: Radiated immunity, 10V/m
EN61000-4-4: Fast transient/burst, ±2KV
EN61000-4-5: Surge, ±1 KV di., ±2 KV com.
EN61000-4-6: Conducted immunity, 10Vrms
EN61000-4-8: Magnec eld immunity, 30 A/m
EN61000-4-11: Voltage dip immunity, 30% reducon for 500ms,
and 100% reducon for 10ms
*Consult with TT Electronics for informaon on addional country safety approvals
Input Specicaons
Input Voltage Range 90 to 264VAC
Input Frequency Range 47 to 63Hz
Input Current 1.2A (rms) for 115 VAC or 0.6A (rms) for 230 VAC
Earth Leakage Current 180μA max. @ 264VAC, 63Hz
Touch Current 100μA max. @ 264 VAC, 63Hz
Output Specicaons
Ripple & Noise
100 mVp-p maximum on 5V, 6V and 9V outputs, 1% maximum on
other voltage outputs (12V, 13.5V …, 48V etc.)
Overvoltage Protecon Provided and set at 112-140% of nominal output voltage
Overcurrent Protecon Protected to short circuit condions
Temperature Coecient ±0.04%/°C maximum
Transient Response
Maximum excursion of 4% or beer on all models, recovering to 1%
of nal value within 500 us aer a 25% step load change
Environmental Specicaons
Operang Temperature 0°C to +60°C (see derang)
Storage Temperature -40°C to +85°C
Relave Humidity 5% to 95% non-condensing
Temperature Derang Derate from 100% at +40°C, Linearly to 50% at +60°C
General Specicaons
Switching Frequency 50-110KHz
Power Factor 0.98 typical
Eciency
85% min. (except 77% min. for PMP90-10, PMP90-10-1, PMP90-11
and PMP90-12)
Hold-up Time 15ms minimum at 110 VAC
Line Regulaon ±0.5% maximum at full load
Inrush Current 50A @ 115VAC or 100A @ 230VAC, at 25°C cold start
Withstand Voltage
5600VDC from input to output (2 MOPP)
2100VDC from input to ground (1 MOPP)
700VDC from output to ground
(To verify AC strength, get correct test method to avoid power sup-
ply damage.) For Class II models, 4000 VAC from input to output)
MTBF
150,000 hours at full load at 25°C ambient, calculated per MIL-
HDBK-217F