FAST RECOVERY RECTIFIERS
DN:T20525A0
http://www.microdiode.com Rev:2020A0 Page :1
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere
FR101S THRU FR107S
Mechanical Data
Features
๏ต
๏ต
๏ต
๏ต
๏ต
๏ต
The plastic package carries Underwriters Laboratory
Flammability Classification 94V-0
Idea for printed circuit board
Fast switching for high efficiency
Low reverse leakage
High forward surge current capability
High temperature soldering guaranteed
250โ/10 seconds at terminals
A-405
Dimensions in inches and (millimeters)
Case : JEDEC A-405 Molded plastic body
T erminals : Solder plated, solderable per MIL-STD-750,Method 2026
Polarity : Polarity symbol marking on body
Mounting Position : Any
Weight
: 0.008 ounce, 0.23 grams
Maximum Ratings And Electrical Characteristics
Ratings at 25ยฐC ambient temperature unlss otherwise specified.
Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%.
0.107(2.7)
0.080(2.0)
DIA.
0.025(0.65)
0.021(0.55)
DIA.
1.0 (25.4)
MIN.
0.205(5.2)
0.166(4.2)
1.0 (25.4)
MIN.
Parameter
SYMBOL S
FR101S FR102S FR103S FR104S FR105S FR106S FR107S
UNI TS
Marking Code
MDD
FR101S
MDD
FR102S
MDD
FR103S
MDD
FR104S
MDD
FR105S
MDD
FR106S
MDD
FR107S
Maximum repetitive peak reverse voltage
V
RRM
50
100 200
400
600 800 1000
V
Maximum RMS voltage
V
RMS
35 70 140
280
420 560 700
V
Maximum DC blocking voltage
V
DC
50 100 200
400
600 800 1000
V
Maximum average forward rectified current
at T
A
=75
โ
I
(AV)
1.0
A
Peak forward surge current
8.3ms single half sine-wave
superimpo sed onrated load (JEDEC Method)
I
FSM
30
A
Maximum instantaneous forward voltage at 1.0A
V
F
1.30
V
T
A
=25โMaximum DC reverse current
at rated DC blocking vol tage
TA=100โ
I
R
5.0
50.0
ฮผA
Maximum reverse recovery time (NOTE 1)
trr
150 250 500
Typical junction capacitance (NOTE 2)
C
J
15.0
pF
Typical thermal resistance (NOTE 3)
R
ฮธ
JA
50.0
โ/W
Operating junction and storage temperature range
T
J
,
T
STG
-65 to +150 โ
Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A
2.Measured at 1MHz and applied reverse voltage of 4.0V D.C.
3.Thermal resistance from junction to ambient at 0.375โ(9.5mm)lead length,P.C.B. mounted
ns
Rev:2020A0 Page :2
Ratings And Characteristic Curves
The curve above is for reference only.
http://www.microdiode.com
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere
FR101S THRU FR107S
1.0
0.8
0.6
0.4
0.2
0
0 25 50 75 100 125 150 175
30
25
20
15
10
5.0
0.6 0.8 1.0 1.2 1.4 1.5
0.1 1.0 10 100
0.01 0.1 1 10 100
100
10
1
0.1
REVERSE VOLTAGE,VOLTS
t,PULSE DURATION,sec.
FIG. 5-TYPICAL JUNCTION CAPACITANCE FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE
FIG. 3-TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
NUMBER OF CYCLES AT 60 Hz
FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
FIG. 1- FORWARD CURRENT DERATING CURVE
AVERAGE FORWARD RECTIFIED CURRENT,
AMPERES
INSTANTANEOUS FORWARD
CURRENT,AMPERES
JUNCTION CAPACITANCE, pF
PEAK FORWARD SURGE CURRENT,
AMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
Single Phase
Half Wave 60Hz
Resistive or
inductive Load
1 10 100
0.01
0.1
1
20
10
TJ=25 C
1
10
100
200
0 20 40 60 80 100
1,000
100
10
1
0.1
0.01
TJ=100 C
TJ=25 C
PERCENT OF PEAK REVERSE VOLTAGE,%
FIG. 4-TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
TRANSIENT THERMAL IMPEDANCE,
C/W
AMBIENT TEMPERATURE, C
TJ=25 C
PULSE WIDTH=300
ยตs
1%DUTY CYCLE
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)