Redpine Signals, Inc. reserves the right to make changes to the product(s) or information contained herein without notice. No Liability is assumed as a
result of their use or application.Redpine, Redpine Signals, the Redpine logo, Driving Wireless Convergence, WiSeConnect and Lite-Fi are trademarks of
Redpine Signals,Inc. All other company names, products and logos are registered trademarks of their respective companies.
© Copyright 2017 Redpine Signals, Inc. All Rights Reserved.
For additional information, please contact Sales at Redpine Signals, Inc.:
Redpine Signals, Inc. • 2107 North First Street • Suite 540 • San Jose, CA 95131
Phone: +1 408 748 3385 • Email: sales@redpinesignals.com
Network Standard Support
IEEE 802.11 a/b/g/n, 802.11j
†
, 802.11d/e/i, 802.11w
†
, 802.1X, 802.11k
†
,
802.11v
†
, 802.11r
†
, 802.11h
†
Bluetooth v2.1 EDR, v4.0
802.15.4-2009 (2.4GHz)
D
ata Rates 802.11n: from 6.5 Mbps to 150 Mbps (MCS 0-7)
802.11a/g: from 6 Mbps to 54 Mbps
802.11b: from 1 Mbps to 11 Mbps
B
luetooth: 1, 2, 3Mbps
8
02.15.4-2009: 250Kbps
Modulation Techniques OFDM with BPSK, QPSK, 16-QAM, 64-QAM
802.11b with CCK and DSSS
Bluetooth: GFSK, DQPSK, 8DPSK
8
02.15.4-2009: DSSS
802.11n Advanced Features 1-SS, 40MHz bandwidth, Greenfield Preamble, Short-GI, 1 spatial stream
STBC, RIFS, A-MSDU, A-MPDU, Aggregation with Block-ack, A-MSDU
inside A-MPDU and Virtual AP support
B
luetooth Advanced Features
†
S
catternet, Adaptive Frequency Hopping, Interlaced scanning,
15 active slaves in proprietary mode, hold, sniff and park modes
ZigBee Advanced Features CCM* security, orphan scanning, coordinator realignment
Wi-Fi modes Wi-Fi client, Access point, Wi-Fi Direct
Bluetooth Modes Master, slave, scatternet
†
Z
igBee Modes ZigBee Coordinator
†
,
Router
†
,
End device
QoS WMM and WMM Power Save Support
Host Interfaces USB 2.0, SPI, UART
Other Peripherals/Interfaces I2C, I2S, SPI, QSPI, USART, GPIO, JTAG, Analog(ADC/DAC) and
Ultra-low-power peripherals.
Supply Voltage 3.0-3.6V, 1.8-3.6V
Operating Temperature Industrial Grade -40ºC to +85ºC
Software and Regulatory Certification Wi-Fi Alliance Compliance (802.11bgn, WPA, WPA2 Personal and
Enterprise, WMM, WMM-PS, WPS, Wi-Fi Direct™, Voice-Personal
β
,
Protected management frames
†
),
Cisco CCX v5
†
,
Bluetooth-SIG Qualification
‡
,
Worldwide Regulatory Compliance:
FCC (IDs are XF6-RS9113SB, XF6-RS9113DB)
IC (IDs are 8407A-RS9113SB, 8407A-RS9113DB)
CE/ETSI,
TELEC
‡
,
SRRC
‡
Typical Transmit Wi-Fi: 18 dBm for 802.11b DSSS
Power(+/-2 dBm) 18 dBm for 802.11g/n OFDM
12 dBm for 802.11a/n OFDM
Bluetooth: 15 dBm
ZigBee : 15 dBm
Rx sensitivity Wi-Fi: 1Mbps -97 dBm (< 8% PER)
(+/- 1dBm) 54 Mbps -76.5 dBm (< 10% PER)
MCS7(20MHz) -73 dBm (< 10% PER)
MCS7(40MHz) -69.5 dBm (< 10% PER)
Bluetooth: 1 Mbps -94 dBm
2 Mbps -92 dBm
3 Mbps -84 dBm
BTLE(1Mbps) -91 dBm
ZigBee: 250 Kbps -102 dBm (< 8% PER)
Wireless Specifications
www.redpinesignals.com
T
he Evaluation Board is designed to configure the module to use the interface on which power supply is
detected. This is indicated through the LEDs mounted on the board.
T
here is a 2-pin inline jumper available for measuring the current being sourced by the module during
different stages of operation. This is labeled as “MEASURE” on the PCB. The user may connect a power
m
eter or an ammeter to this jumper to measure the current.
T
he USB drive is bootable. It is loaded with Fedora Core 18 OS with the OneBox-Mobile driver binaries
included for evaluation of n-Link
®
modules on a standard PC/Laptop platform.
T
he USB drive also has the release package for the Connect-io-n
®
/
WiSeConnect
®
m
odules which
includes the firmware, documentation and reference projects for multiple platforms.
Redpine provides drivers for multiple OS’s and MCU platforms for the n-Link
®
modules and also OS-less
MCU platforms for WiSeConnect
®
modules. The software provided in this kit is to enable easy and quick
evaluation on a PC. Please contact Redpine Signals’ Sales (sales@redpinesignals.com) for availability of
drivers for an OS and MCU of your choice.
Evaluation Board
†: These features are not supported by current software releases. Contact Repine Signals Sales
(sales@redpinesignals.com) for details.
‡
:
These certifications are in progress at this time. Contact Redpine Signals Sales
(sales@redpinesignals.com) for more details and for certifications not listed here.
β
:
Applicable to n-Link
®
modules only
Ordering Information
Related Links:
z
RS9113 n-Link
®
Module Product Brief
z
RS9113 Connect-io-n
®
Module Product Brief
z
RS9113 WiSeConnect
®
Module Product Brief
Part Numbers