Instruction manual
Rack Mount Adapter KRA1-PWX HALF SINGLE / KRA1-PWX HALF PAIR
This product is a rack mount adapter for attaching one or two Kikusui PWX Series Regulated DC Power Supplies to a rack.
• KRA1-PWX HALF SINGLE (1 unit): This can be used with JIS millimeter racks and EIA inch racks.
• KRA1-PWX HALF PAIR (2 units): This can be used with JIS millimeter racks and EIA inch racks.
Components
Check that all parts are included and that they are not damaged. If any of the parts are damaged or missing, contact your Kikusu i
agent or distributor.
Assembly
Carry out the procedure below to attach the adapter to the PWX Series and mount it on the rack.
1 Remove the rubber feet for the bottom of the PWX Series.
2 Attach the parts using the included screws of the PWX Series.
■ When attaching one power supply to a rack
Use #10-32 screws to attach the blank panel to the power supply. Use M4 screws to attach the handles and the rack mount
brackets to the power supply.
No. Parts Code Description
Quantity
SINGLE PAIR
1 B9-000-168 Blank panel PWX 1U 1
─
2 B9-000-167 Support board
─
1
3 B9-000-170 Rack mount bracket (R) KRB1-PWX (R) 1
4 B9-000-171 Rack mount bracket (L) KRB1-PWX (L) 1
5 E6-000-027 Handle 2
6 M2-101-008 Support board screw (M3x6)
─
4
7 M2-101-015 Handle and Rack mount bracket screw (M4x8) 8
8 M3-112-043 Rack mount screw (M5x14) 4
9 M2-110-006 Blank panel screw (#10-32x3/ 8) 3
─
10 M5-100-005 Blank panel washer (M5) 3
─
11 M5-101-005 Blank panel spring washer (M5) 3
─
Rubber foot (4 locations)
Screw (M3)
(4 locations)
Loosen the screws to remove the
rubber feet (in four locations).
M4 screw (4 locations)
M4 screw (4 locations)
Rack mount bracket (L)
Rack mount bracket (R)
M5 spring washer (3 locations)
#10-32 screw (3 locations)
M5 washer (3 locations)
Blank panel
Handle (2 locations)
■ When attaching two power supplies to a rack
Use M4 screws to attach the handles and the rack mount brackets to the power supplies. Use M3 screws to attach the
support board to the power supplies.
3 Attach the PWX series to the rack using the M5 screws.
The instrument may fall. Install the suitable support angles apply-
ing to the used rack system to support the instrument.
Outline drawing
KIKUSUI ELECTRONICS CORP.
1-1-3, Higashiyamata, Tsuzuki-ku, Yokohama, 224-0023, Japan
TEL : +81-45-482-6353 Fax : +81-45-482-6261
www.kikusui.co.jp/en
■ When attaching the power supply to
a JIS millimeter rack
Use M5 screws in the center grooves to attach
the power supplies to the rack.
■ When attaching the power supply to
an EIA inch rack
Use M5 screws in the upper and lower holes
to attach the power supplies to the rack.
M4 screw (4 locations)
M4 screw (4 locations)
M3 screw (4 locations)
Rack mount bracket (L)
Rack mount bracket (R)
Handle (2 locations)Support board
There are two spare
screws.
M5 screw (2 locations)
Use the center
grooves to attach
the power supplies
to the rack.
Use the upper and
lower holes to
attach the power
supplies to the rack.
M5 screw (2 locations)
Support angle
Instrument
CAUTION