Technical Data Sheet

LOCTITE ECCOBOND FP0087

September-2016

PRODUCT DESCRIPTION

LOCTITE ECCOBOND FP0087 provides the following product

characteristics:

Technology Epoxy

Appearance Black

Product Benefits • Low stress

• High glass transition

• Low thermal expansion

• Excellent moisture resistance

• Excellent thermal shock resistance

• Reduced warpage and cracking

Filler Weight, % 76

Components One-component

Cure Heat cure

Application Encapsulation

Typical Applications Encapsulant for potting stress sensitive

devices

LOCTITE ECCOBOND FP0087 yields best results when used

to encapsulate a device enclosed in a cavity or potting ring,

which restricts the flow of the material. The unique combination

of low stress and excellent resistance to moisture and process

fluids provide excellent results in severe automotive

environments.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Viscosity, Brookfield - RVF, 25 °C, mPa·s (cP):

Spindle 6, speed 20 rpm 20,000

Shelf Life @ -40°C, months 9

Gel Time @ 121ºC, minutes 20

Pot Life @ 25ºC, 200 grams mass, hours 24

Specific Gravity @ 25ºC gm/cc 1.78

Flash Point - See SDS

TYPICAL CURING PERFORMANCE

Recommended Cure Schedule

1 hour @ 125°C plus

1 hour @ 180°C

The above cure profile is a guideline recommendation. Cure

conditions (time and temperature) may vary based on customers'

experience and their application requirements, as well as customer

curing equipment, oven loading and actual oven temperatures.

TYPICAL PROPERTIES OF CURED MATERIAL

Physical Properties

Coefficient of Thermal Expansion , ppm/°C

ISO 11359-2,:

Below Tg (40 to 120°C) 18

Glass Transition Temperature, ISO 11359-2

(Tg), °C

175

Shore Hardness, ISO 868, Durometer D 95

Electrical Properties

Dielectric Constant / Dissipation Factor, IEC 60250:

1-kHz 3.34 / 0.003

10-kHz 3.32 / 0.006

100-kHz 3.2 / 0.014

Volume Resistivity, IEC 60093, Ω·cm 6.34×10

Surface Resistivity, IEC 60093, Ω 7.10×10

GENERAL INFORMATION

For safe handling information on this product, consult the Safety

Data Sheet, (SDS).

This product is not recommended for use in pure oxygen and/or

oxygen rich systems and should not be selected as a sealant for

chlorine or other strong oxidizing materials.

Not for product specifications

The technical data contained herein are intended as reference only.

Please contact your local quality department for assistance and

recommendations on specifications for this product.

THAWING:

1. Frozen packages must be completely thawed before use.

2. Allow container to reach room temperature before use.

3. Store tip down and warm at room temperature until no longer

cool to the touch (normally 20 to 60 minutes).

4. DO NOT thaw in an oven.

Directions for use

1. For best results, dispense onto substrate warmed to 80°C.

2. Warm LOCTITE ECCOBOND FP0087 to 30 to 40°C for faster

dispensing.

3. NOTE: Elevated temperatures reduce working life.

STORAGE:

Store product in the unopened container in a dry location. Storage

information may be indicated on the product container labeling.

Optimal Storage : -40 °C

Material removed from containers may be contaminated during use.

Do not return product to the original container. Henkel Corporation

cannot assume responsibility for product which has been contaminated

or stored under conditions other than those previously indicated. If

additional information is required, please contact your local Technical

Service Center or Customer Service Representative.

TDS LOCTITE ECCOBOND FP0087, September-2016

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

N x 0.225 = lb

N/mm x 5.71 = lb/in

psi x 145 = N/mm²

MPa = N/mm²

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Disclaimer

Note:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The product

can have a variety of different applications as well as differing application and

working conditions in your environment that are beyond our control. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and

Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is

applicable:

The data contained herein are furnished for information only and are believed to

be reliable. We cannot assume responsibility for the results obtained by others

over whose methods we have no control. It is the user's responsibility to

determine suitability for the user's purpose of any production methods mentioned

herein and to adopt such precautions as may be advisable for the protection of

property and of persons against any hazards that may be involved in the handling

and use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties of

merchantability or fitness for a particular purpose, arising from sale or use

of Henkel Corporation’s products. Henkel Corporation specifically

disclaims any liability for consequential or incidental damages of any kind,

including lost profits. The discussion herein of various processes or

compositions is not to be interpreted as representation that they are free from

domination of patents owned by others or as a license under any Henkel

Corporation patents that may cover such processes or compositions. We

recommend that each prospective user test his proposed application before

repetitive use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

Trademark usage

Except as otherwise noted, all trademarks in this document are trademarks of

Henkel Corporation in the U.S. and elsewhere.

denotes a trademark

registered in the U.S. Patent and Trademark Office.

Reference 1

Americas

+1.888.943.6535

Europe

+32.1457.5611

Asia

+86.21.3898.4800

For the most direct access to local sales and technical support visit: www.henkel.com/electronics