Technical Data Sheet

LOCTITE

Frekote

C-600™

Known as Aqualine

C-600 ™

October-2015

PRODUCT DESCRIPTION

LOCTITE

Frekote

C-600™ provides the following product

characteristics:

Technology Mold Release

Appearance Milky white emulsion

LMS

Chemical Type Water based emulsion

Odor Mild

Cure Room temperature cure

Cured Thermal Stability ≤315 °C

Application Release Coatings

Application Temperature 20 to 40 °C

Specific Benefit ● Non-flammable

● Autoclaved resistant at either

121°C or 177°C

● Multiple releases

LOCTITE

Frekote

C-600™ mold release agent is a

proprietary, water based emulsion originally developed for

releasing large scale parts such as wind blades, and is ideal for

numerous other high performance composite structures. When

fully cured, this product chemically bonds to the mold surface

to form a thin, inert, thermally stable coating. LOCTITE

Frekote

C-600™ is designed to be applied and cured at

ambient shop temperatures.

TYPICAL PROPERTIES OF UNCURED MATERIAL

Specific Gravity @ 20 °C 0.97 to 1.03

LMS

Flash Point - See SDS

TYPICAL PROPERTIES OF CURED MATERIAL

4 total coats applied @ 22°C, 5 minute cure per coat, and final 30

minute cure @ 22°C

Epoxy Release Test ≥5

LMS

GENERAL INFORMATION

For safe handling information on this product, consult the

Safety Data Sheet (SDS).

Mold Preparation

Cleaning:

Mold surfaces must be thoroughly cleaned and dried. All traces

of prior release must be removed. This may be accomplished

by using Loctite

Frekote

PMC or other suitable cleaner.

Loctite

Frekote

915WB™ or light abrasives can be used for

heavy build-up.

Directions for use:

1. Wipe on a smooth, thin continuous, wet film.

2. Wait 1-2 minutes before the coating is fully dried, then

lightly wipe off the coated surface with a new wipe.

3. Allow a minimum of 15 minutes before applying next coat.

Apply a minimum of 3 coats in this manner. Dampen cloth

lightly as needed.

4. Allow the final coat to cure for 30 minutes at 22°C.

5. The release agent can also be spray applied. Wiping off is

not necessary. 2-3 coats are needed for a new mold. One

coat is needed for touch-ups. Curing between coats is

5-10 minutes, until the coating dries. The final curing time

is 30 minutes.

Mold Touch up

Touch up coats should only be applied to areas where poor

release is noticed and should be applied using the same

method as base coats. This will reduce the possibility of

release agent or polymer build-up. The frequency of touch ups

will depend on the polymer type, mold configuration, and

abrasion parameters.

Loctite Material Specification

LMS

LMS dated July-30, 2009. Test reports for each batch are

available for the indicated properties. LMS test reports include

selected QC test parameters considered appropriate to

specifications for customer use. Additionally, comprehensive

controls are in place to assure product quality and

consistency. Special customer specification requirements may

be coordinated through Henkel Quality.

Storage

Store product in the unopened container in a dry location.

Storage information may be indicated on the product container

labeling.

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

Corporation cannot assume responsibility for product which

has been contaminated or stored under conditions other than

those previously indicated. If additional information is required,

please contact your local Technical Service Center or

Customer Service Representative.

TDS LOCTITE

Frekote

C-600™, October-2015

Conversions

(°C x 1.8) + 32 = °F

kV/mm x 25.4 = V/mil

mm / 25.4 = inches

µm / 25.4 = mil

N x 0.225 = lb

N/mm x 5.71 = lb/in

N/mm² x 145 = psi

MPa x 145 = psi

N·m x 8.851 = lb·in

N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in

mPa·s = cP

Note:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. The product

can have a variety of different applications as well as differing application and

working conditions in your environment that are beyond our control. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Belgium NV, Henkel Electronic

Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and

Henkel France SA please additionally note the following:

In case Henkel would be nevertheless held liable, on whatever legal ground,

Henkel’s liability will in no event exceed the amount of the concerned delivery.

In case products are delivered by Henkel Colombiana, S.A.S. the following

disclaimer is applicable:

The information provided in this Technical Data Sheet (TDS) including the

recommendations for use and application of the product are based on our

knowledge and experience of the product as at the date of this TDS. Henkel is,

therefore, not liable for the suitability of our product for the production processes

and conditions in respect of which you use them, as well as the intended

applications and results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other

written or oral recommendation(s) regarding the concerned product is excluded,

except if otherwise explicitly agreed and except in relation to death or personal

injury caused by our negligence and any liability under any applicable mandatory

product liability law.

In case products are delivered by Henkel Corporation, Resin Technology

Group, Inc., or Henkel Canada Corporation, the following disclaimer is

applicable:

The data contained herein are furnished for information only and are believed to

be reliable. We cannot assume responsibility for the results obtained by others

over whose methods we have no control. It is the user's responsibility to

determine suitability for the user's purpose of any production methods mentioned

herein and to adopt such precautions as may be advisable for the protection of

property and of persons against any hazards that may be involved in the handling

and use thereof. In light of the foregoing, Henkel Corporation specifically

disclaims all warranties expressed or implied, including warranties of

merchantability or fitness for a particular purpose, arising from sale or use

of Henkel Corporation’s products. Henkel Corporation specifically

disclaims any liability for consequential or incidental damages of any kind,

including lost profits. The discussion herein of various processes or

compositions is not to be interpreted as representation that they are free from

domination of patents owned by others or as a license under any Henkel

Corporation patents that may cover such processes or compositions. We

recommend that each prospective user test his proposed application before

repetitive use, using this data as a guide. This product may be covered by one or

more United States or foreign patents or patent applications.

Trademark usage

Except as otherwise noted, all trademarks in this document are trademarks of

Henkel Corporation in the U.S. and elsewhere.

denotes a trademark

registered in the U.S. Patent and Trademark Office.

Reference 0.2

Americas

+860.571.5100

Europe

+49.89.320800.1800

Asia

+86.21.2891.8863

For the most direct access to local sales and technical support visit www.henkel.com/industrial