Technical Data Sheet
LOCTITE
®
Frekote
®
CMR™
Known as Frekote CMR
October-2015
PRODUCT DESCRIPTION
LOCTITE
®
Frekote
®
CMR™ provides the following product
characteristics:
Technology Mold Release
Appearance Clear, colorless light yellow
LMS
Chemical Type Solvent Based Polymer
Odor Solvent
Cure Room temperature cure
Application Release Coatings
Application Temperature 13 to 41 °C
Specific Benefit ● Easy application
● Fast curing
● High gloss finish
LOCTITE
®
Frekote
®
CMR™ is a unique, polymer release
agent containing a special blend of resins and cleaning
solvents designed to dissolve and remove polymer,composite,
and other residues from polyester molds without dulling the
mold surface. LOCTITE
®
Frekote
®
CMR™ is highly
recommended for cleaning polyester mold surfaces with mold
build-up resulting from repeated releases using Frekote
®
WOLO™. Additional releases can be obtained after cleaning
the mold without touching up with a traditional mold release
agent.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Specific Gravity @ 25 °C 0.789
LMS
Flash Point - See SDS
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Safety Data Sheet (SDS).
Directions for use:
FRP Molds and Wax Removal
1.
LOCTITE
®
Frekote
®
CMR™ should be applied to the
mold surface with a clean lint free cloth.
2. Wax and other mold residue will immediately begin to
dissolve and should be removed from the surface with a
second clean cloth while it is still dissolved in the
LOCTITE
®
Frekote
®
CMR™.
3. As the cloth becomes saturated with wax and mold
residue, dispose of it and use a new cloth.
4. Repeat process until composite and other mold residue is
removed.
5.
Allow LOCTITE
®
Frekote
®
CMR™ to cure a minimum of
15 minutes at 20°C.
6. The mold is now ready for use.
7. NOTE:
A simple test to assess the effectiveness of the Frekote
®
interface is the use of masking tape. A good interface will
prevent any significant degree of tape adhesion.
Loctite Material Specification
LMS
LMS dated September-6, 2006. Test reports for each batch
are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
The product is classified as flammable and must be stored in
an appropriate manner in compliance with relevant
regulations. Do not store near oxidizing agents or combustible
materials. Store product in the unopened container in a dry
location. Storage information may also be indicated on the
product container labelling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
cannot assume responsibility for product which has been
contaminated or stored under conditions other than those
previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representive.
TDS LOCTITE
®
Frekote
®
CMR™, October-2015
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Corporation, Resin Technology
Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks of
Henkel Corporation in the U.S. and elsewhere.
®
denotes a trademark
registered in the U.S. Patent and Trademark Office.
Reference 0.1
Americas
+860.571.5100
Europe
+49.89.320800.1800
Asia
+86.21.2891.8863
For the most direct access to local sales and technical support visit www.henkel.com/industrial