JK-SP2***/JK-SS2*** YRS-370 – – – – – – KEJ-0.7 for plug, KEJ-0.4 for socket –

J-SP1***/J-SS1*** YRS-440 YC-440 – – – – J-BP/BS1*** DEJ-0.3 –

J-SP2***/J-SS2*** YRS-330 – – – – – – DEJ-0.3 –

LFO-1.0-250N – –––– JUCS-FO – – –

LFO-2.5-250N – –––– JUCS-FO – – –

MD-SP12** YRS-470 – – – – – – MEJ-06 –

MD-SP22** YRS-460 – – – – – – MEJ-06 –

RA-SC1290 YRS-231 –

YRM-232

–– –RA-BC12** EJ-RA –

YRM-233

RF-SC22** ––YRM-230 – – – RF-BC22** – –

RPJ-SP2331

YRS-331 – – – – – – EJ-RPJ –

RPJ-SS2331

SAA-21(T)-** – YC-141 – – – – LAA-21(T-)** – –

SAA-50(T)-** – YC-182 – – – – LAA-50(T)-** – –

SAA-51(T)-** – YC-142 – – – – LAA-51(T)-** – –

SAB-51(T)-** – YC-142 – – – – LAB-51(T)-** – –

SACH-003G-P0.2 YRS-1190 – – – – – – – –

SAGH-002GU-P0.3 YRS-858 – – – – – – – –

SAN-002T-0.8A

YRS-220 – – – – – – EJ-PH –

SAN-002T-0.8K

SBH-001T-P0.5 – YC-670R – – – WC-670 BBH-001T-P0.5 – –

SBHL-002T-P0.5 YRS-857 – – – – – – – –

SBHM-001T-P0.5 – YC-670R – – – – BBHM-001T-P0.5 EJ-BHMR –

SBHS-002T-P0.5A YRS-852 – – – – – – EJ-BHS2 –

SBHS-002T-P0.5A – ––––––EJ-BHS2 –

SBHSM-002T-P0.5 YRS-854 – – – – – – EJ-BHSW –

SBHT-002T-P0.5

YRS-856

––––––EJ-BHT –

YRS-857

SBN-001T-1.0 YRS-170 YC-170R –

–

–– – BBN-001T-1.0 – –

SCN-001T-1.0K

YRS-191 YC-191R – – – WC-191

BCN-001T-1.0K

––

SCN-001T-P1.0 BCN-001T-P1.0

SCS-41T-2.3 – ––––––CSJ-23 –

SCSH-002T-P0.2N YRS-1350 – – – – – – – –

Hand tools

Crimping tools

Extraction tool

Terminals and parts model

number in alphabetical order

Insertion tool

Hand tools Hand tools

for chain terminals for loose piece terminals for loose piece terminals

Extraction and Insertion tools

YRS

series

Insertion tool allows contacts be inserted

in the housing.

This tool greatly increases efficiency especially

when thin wires are used.

Extraction tool is used to extract

contacts improperly inserted in the housing.

Note: (1) These tools are for prototype tooling or repair.

(2) YC tool has two crimping sections (A and B). YRS tool has also two crimping sections by inverting upper dies.

Be sure to check applicable wires before use. Since the dies are fixed, the crimping height cannot be adjusted. Therefore, some of the

applicable wires described in this catalog may not be crimped properly.

Before use, check for proper crimping (such as tensile strength, terminal/contact deformation).

(3) These tools are not applicable to 2-wire crimping.

(4) When hand crimping board-in terminals (SAN, SCN, SDN, SGN, SIN, SJN, SZN), care should be taken not to contaminate the solder tails of

the terminals, as with greasy or oily fingers. If a solder problem arises, some cleaning of the tips of the terminal is advisable.

(5) WC and JUC hand tools are provided by J.S.T.(U.K.) LTD. and contact them about the details of these hand tools.

Dimensions:

(W×L) 59×224 mm

series

Dimensions:

(W×L) 70×296 mm

YRM

series

Dimensions:

(W×L) 59×224 mm

YRF

series

Dimensions:

(W×L) 70×295 mm

80×305 mm

YRS series YC series YRM series YRF series

WC & JUC series

JUK's Hand Tools

Terminal in loose form

model No.

Crimping tools

It is the manual tool that is convenience to terminate very small quantity of contacts for prototype or maintenance.

It is composed of two crimping dies for the conductor and insulation, and can be crimp easily.

YRK and YRK-EX can be used for mass-production.

YRK

YRK-EX series

Note: Contact JST for wire range.

YRK

series

Dimensions:

(W×L×D)

75×314×25 mm

Dimensions:

(W×L×D)

75×314×25 mm

YRK-EX

series