Datasheet

Sure Cross

Wireless Q45 Sensors combine the best of Banner’s flexible Q45 sensor family with its reliable, field-proven,

Sure Cross wireless architecture to solve new classes of applications limited only by the user’s imagination. Containing a

variety of sensor models, a radio, and internal battery supply, this product line is truly plug and play.

The Wireless Q45 Sensor with Button and Light as a wireless node with independently

controlled push button input and a four-color LED indicator light. The push button can be

configured with DIP switches for either toggle or momentary operation; the red, yellow,

green, and blue LED indicator light outputs can be configured for solid or flashing

operation.

Available Models

• DX80N9Q45BL-RYGB

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel

protection. Doing so could lead to serious injury or death.

This device does not include the self-checking redundant circuitry

necessary to allow its use in personnel safety applications. A sensor

failure or malfunction can cause either an energized or de-energized

sensor output condition.

Storage Mode for the Wireless Q45 Sensors

While in storage mode, the Wireless Q45 Sensor's radio does not operate. All Wireless Q45 Sensors ship from the factory

in storage mode to conserve the battery. To wake the device, press and hold the button for five seconds. To put any

Wireless Q45 Sensor into storage mode, press and hold the button for five seconds. The Wireless Q45 Sensor is in storage

mode when the LEDs stop blinking.

Button, LEDs, and DIP Switches (Button with Light Model)

Button

2 Red LED (flashing) indicates a radio link error with the Gateway.

3 Green LED (flashing) indicates a good radio link with the Gateway.

4 Amber LED indicates when input 1 is active. The LED is active at power up and disabled

after 15 minutes to conserve power. To enable the LED for another 15 minutes, press

button once. To disable the LED, press the button 5 times.

5 DIP Switches

DIP Switch Settings

After making any changes to any DIP switch position, reboot the Wireless Q45 Sensor by triple-clicking the button, waiting

a second, then double-clicking the button.

As shown in the image above, the DIP switches are in the OFF position. To turn a DIP switch on, push the switch toward

the battery pack. DIP switches one through four are numbered from left to right as shown above.

Sure Cross

Wireless Q45 Sensor - Button/

Light

Original Document

192693 Rev. A

26 January 2016

192693

Description DIP Switches

1 2 3 4 5 6 7 8

Transmit power: 1 Watt OFF *

Transmit power: 250 mW (compatible with 150 mW radios) ON

Reserved OFF * OFF * OFF *

Reserved (keep in OFF position) OFF *

Button mode: toggle OFF *

Button mode: momentary ON

Reserved (keep in OFF position) OFF *

Light mode: flash (recommended to conserve the battery)

OFF *

Light mode: solid ON

* Default position

Modbus Register Table

I/O #

Modbus Holding Register I/O Type I/O Range Holding Register

Representation

Gateway Any Node Min. Value Max.

Value

Min. (Dec.) Max. (Dec.)

1 1 1 + (Node# × 16) Discrete IN 1 0 1 0 1

2 2 2 + (Node# × 16) NOT Discrete IN 1 0 1 0 1

...

7 7 7 + (Node# × 16) Reserved

8 8 8 + (Node# × 16) Device Message

9 9 9 + (Node# × 16) Discrete OUT 1 (red light) 0 1 0 1

10 10 10 + (Node# × 16) Discrete OUT 2 (yellow light) 0 1 0 1

11 11 11 + (Node# × 16) Discrete OUT 3 (green light) 0 1 0 1

12 12 12 + (Node# × 16) Discrete OUT 4 (blue light) 0 1 0 1

...

15 15 15 + (Node# × 16) Control Message

16 16 16 + (Node# × 16) Reserved

Replacing the Batteries

To replace the lithium "AA" cell battery, follow these steps.

As with all batteries, these are a fire, explosion, and severe burn hazard. Do not burn or expose them to high

temperatures. Do not recharge, crush, disassemble, or expose the contents to water. Properly dispose of used batteries

according to local regulations by taking it to a hazardous waste collection site, an e-waste disposal center, or other facility

qualified to accept lithium batteries.

The light consumes most of the sensor's power. If the light remains off most of the time, the batteries will last much longer.

Sure Cross

Wireless Q45 Sensor - Button/Light

2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 192693 Rev. A