SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER
VOLTAGE RANGE
50 to 1000 Volts
GBJ10005 THRU GBJ1010
CURRENT 10.0 Amperes
FEATURES
• Plastic package has UL Flammability
Glassification 94V-0
• Glass passivated chip junctions
• High case dielectric strength of 1500 VRMS
• High surge current capability
• Ideal for printed circuit boards
• High temperature soldering guaranteed
260℃/10 seconds, 0.375”(9.5mm) lead length
MECHANICAL DATA
• Case: molded plastic body
• Terminal: Plated leads solderable per MIL-STD-750
Method 2026
• Mounting position: Any (Note 3)
• Mounting Torque: 6 in – 1bs max.
• Weight: 0.15 ounce,4.0 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
• Ratings at 25℃ ambient temperature unless otherwise specified
• Single Phase, half wave, 60Hz, resistive or inductive load
• For capacitive load derate current by 20%
SYMBOLS
GBJ
10005
GBJ
1001
GBJ
1002
GBJ
1004
GBJ
1006
GBJ
1008
GBJ
1010
UNIT
Maximum Reverse Peak Repetitive Voltage
V
RRM
50 100 200 400 600 800 1000
Volts
Maximum RMS Voltage
V
RMS
35 70 140 280 420 560 700 Volts
Maximum DC Blocking Voltage
V
DC
50 100 200 400 600 800 100 Volts
10 Maximum Average Forward At T
C
=100℃(Note 1)
Rectified Current, At T
A
=40℃(Note 2)
I
(AV)
5.0
Amps
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC Method)
I
FSM
170 Amps
Rating for Fusing (t＜8.3ms)
I
2
t 142 A
2
s
Maximum Instantaneous Forward Voltage drop
Per bridge element 5.0A
V
F
1.0 Volts
TA=25℃
5.0
Maximum DC Reverse Current at
rated DC blocking voltage per element
TA=125℃
I
R
250
μA
Typical Junction Capacitance, per let
(Measured at 1.0MHz and applied reverse voltage of
4.0V)
C
J
60
pF
Typical Thermal Resistance (Note 2 and 3)
R
JC
2.2
℃/W
Operating Junction Temperature Range
T
J
(-55 to +150)
℃
Storage Temperature Range
T
STG
(-55 to +150)
℃
Notes: 1. Unit mounted on 150mm×150mm×1.6mm A1. Plate heatsink
2. Unit mounted on P.C.B. With 0.5×0.5”(1.2×1.2mm) copper pads and 0.375”(9.5mm) lead length
3. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum
Heat transfer with #6 screw
29.7-30.3
2.5±0.2
2.0-2.4
0.9-1.1
9.8-10.2 7.3-7.7
7.3-7.7
3.0×45
4.4-4.8
3.4-3.8
2.7-3.1
0.6-0.8
19.7-20.3
10.8-11.2
3.8-4.2
17.0-18.0
φ
3
.
1
-
3
.
4
5.0
GBJ
O
O
Web Site: www.hkmic.com
SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER
VOLTAGE RANGE
50 to 1000Volts
GBJ10005 THRU GBJ1010
CURRENT 10.0 Amperes
RATINGS AND CHARACTERISTIC CURVES GBJ10005 THRU GBJ1010
1
0.1
100
10.1
0.01
10
110
100
10
1000
100
1
0.01
0.1
1
10
100
10080
60
4020
0
100
10
1
0.1
0.01
1.41.21.00.8
0.6
200
100
0
100
2040608
642
10
1
175
10
0
5
15
1257525
0
50150100
A
T =25℃
A
T =125℃
1.0 Cycle
P.C.B. Mounting
Heat-Sink Mounting. Tc
REVRESE VOLTAGE,(V)
T, HEATING TIME (SEC.)
PER LEG
INSTANTANEOUS FORWARD VOLTAGE,(V)
FIG. 5- TYPICAL JUNCTION CAPACITANCE
PERCENT OF RATED PEAK REVERSE VOLTAGE,(V)
FIG. 6- TYPICAL TRANSIENT THERMAL
IMPEDANCE
FIG. 3- TYPICAL FORWORD
CHARACTERISTICS PER LGE
TEMPERATURE, ℃
NUMBER OF CYCLES AT 60 Hz
PER LEG
FIG. 4- TYPICAL REVERSE CHARACTERISTICS
FIG. 1- DERATING CURVE
RECTIFIED CURRENT
OUTPUT FORWARD SURGE CURRENT PER LEG
FIG. 2- MAXIMUM NON-REPETITIVE PEAK
AVERAGE FORWARD OUTPUT
CURRENT
(
A
)
INSTANTANEOUS FORWARD
CURRENT, (A)
JUNCTION CAPACITANCE,
(
pF
)
CURRENT,(A)
PEAK FORWARD SURGE,
CURRENT, (A)
INSTANTANEOUS REVERSE
TRANSIENT THERMAL IMPEDANCE
(
℃/W
)
Web Site: www.hkmic.com