Dimensions: [mm]

sectional drawing A-A

10,0

115,0

17,5

60,0

Scale - 1:2,5

Würth Elektronik eiSos GmbH & Co. KG

EMC & Inductive Solutions

Max-Eyth-Str. 1

74638 Waldenburg

Germany

Tel. +49 (0) 79 42 945 - 0

www.we-online.com

eiSos@we-online.com

CREATED CHECKED GENERAL TOLERANCE PROJECTION

METHOD

DaSc SuPe DIN ISO 2768-1m

DESCRIPTION

WR-WST IDC Press Aluminium

Adapter for IDC press (T-slot)

ORDER CODE

4900004

REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE

001.000 Valid 2018-08-31 eiCan 1/3

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH

& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety

must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.

Cautions and Warnings:

The following conditions apply to all goods within the product services of the Connectors

of Würth Elektronik eiSos GmbH & Co. KG:

General:

• This electronic component is designed and developed with the intention for use in general electronics equipment.

• Before incorporating the components into any equipment in the field such as military, aerospace, aviation, nuclear control, submarine,

transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information

network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body,

Wurth Elektronik must be asked for a written approval.

• In addition, even electronic component in general electronic equipment, when used in electrical circuits that require high safety,

reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed by the user before usage.

• The connector is designed and manufactured to be used within the datasheet specified values.

• Do not use the connector outside the datasheet specifications.

• Prevent any damage or scratches on the connector, especially on the actuator.

• Direct mechanical impact to the product shall be prevented (e.g overlapping of the PCB´s).

• The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the

authority of the customer. All technical specification for standard products do also apply to customer specific products.

• Würth Elektronik products are qualified according to international standards which are listed into each product reliability report.All

products characteristics are therefore given according to results obtained throughout these detailed test protocols. May any product

characteristic be qualified by the customer, out of given Würth Elektronik specifications, Würth Elektronik cannot ensure its validity and

sustainability over time.

• The Connectors are designed to be used along with Würth Elektronik counterparts and tools. Würth Elektronik cannot insure the

reliability of these components while being used with other products.

Product Specific:

Soldering:

• The solder profile must comply with the Würth Elektronik technical soldering specification, otherwise this will void the warranty.

• Other soldering methods are not verified and have to be validated by the customer at his own risk.

Cleaning and Washing:

• Parts are not constructed for washing, so washing can cause malfunction afterwards.

• Cleaning agent that are used to clean the customer applications might damage or change the characteristics of the component, body,

pins and termination.

• Please do not submerse our washable products into water or cleaning agents or put them in locations exposed to water completely.

• When cleaning by hand (brushing), please do not use excessive force on our connectors to avoid malfunction afterwards, because

customer could deform function relevant areas.

• We recommended a solution without organic acid (preserve the plating against corrosion) volatile, without residues and compatible with

the plastic.

• We recommend to perform tests and to let a part in immersion in the solution 8 to 12 hours and see if there is a degradation.

Storage Conditions:

• The Connectors are considered MSL1 into closed original packaging and are not subject to storage time limits regarding the moisture

sensivity but all products shall be used before the end of the period of 12 months based on the products date code, if not 100%

solderability can’t be warranted.

Handling:

• Do not repeatedly operate the connector with excessive force. It may damage or deforms the contact dome which results in malfunction.

• In the case a product requires particular handling precautions, in addition to the general recommendations mentioned here before, these

will appear on the product datasheet.