Datasheet
The DXM100-S1 Modbus Slave can connect directly to an RS-485 serial bus or to a wireless
ISM network as a remote Modbus Slave device.
• Power options include 12 to 30 V dc with or without a battery backup, or 12 V dc solar
panel with a sealed lead acid battery
• Local I/O options: universal inputs, NMOS outputs, and analog outputs (0 to 10 V or 4
to 20 mA)
• ISM radios available in either a 900 MHz band or 2.4 GHz band for local wireless
networks
WARNING:
• Do not use this device for personnel protection
• Using this device for personnel protection could result in serious injury or death.
• This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-
energized (off) output condition.
Important:
• Never operate a 1 Watt radio without connecting an antenna
• Operating 1 Watt radios without an antenna connected will damage the radio circuitry.
• To avoid damaging the radio circuitry, never apply power to a Sure Cross
®
Performance or Sure Cross
MultiHop (1 Watt) radio without an antenna connected.
Important:
• Electrostatic discharge (ESD) sensitive device
• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include leaving
devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and
assembling units on a grounded, static-dissipative surface.
Model Key for the DXM100-S1 Models
S1 =
Radio
Configuration
S1
Base
DXM100-
R2
Blank = None
R2 = 900 MHz, 1 W HE5 MultiHop Data Radio (North America)
R4 = 2.4 GHz, 65 mW HE5 MultiHop Data Radio (Worldwide)
R5 = 900 MHz, 65 mW HE5L MultiHop Data Radio (Used for M-GAGE networks)
R9 = 900 MHz, MultiHop Radio approved for Australia/New Zealand
Modbus slave I/O device for MultiHop wireless
networks or wired networks
Power: 12−30 V dc/Solar/Battery
Comms: RS-485
Inputs: (4) Universal IN
Outputs: (4) NMOS OUT, (2) Analog OUT (0–10 V or 4–20 mA)
Power Out: (2) Selectable 5 V or 16 V switched power,
(1) 5 V courtesy power
Some example models include, but are not limited to, the following:
Models
Description
DXM100-S1 DXM100-S1 Modbus Slave
Sure Cross
®
DXM100-S1 Wireless Modbus Slave
Original Document
195454 Rev. E
20 December 2018
195454
Models Description
DXM100-S1R2 DXM100-S1 Modbus Slave base with MultiHop ISM 900 MHz radio
DXM100 Documentation
For more information about the DXM100 Slave family of products, please see additional documentation and videos on the Banner
website:
www.bannerengineering.com
.
• DXM Wireless Controller Sell Sheet, p/n
194063
• DXM100-B1 Wireless Controller Datasheet, p/n
186724
• DXM100-B2 Wireless Controller Datasheet, p/n
195232
• DXM100-Bx Wireless Controller Instruction Manual, p/n
190037
• DXM100-S1 Modbus Slave Datasheet, p/n
195454
• DXM100-S2 Modbus Slave Datasheet, p/n
195231
• DXM100-Sx Modbus Slave Instruction Manual, p/n
188231
• DXM ScriptBasic Instruction Manual, p/n
191745
• DXM Controller Configuration Quick Start, p/n
191247
• DXM Configuration Tool software (p/n
b_4447978
)
• DXM
Configuration Tool Instruction Manual, p/n
158447
• DXM EDS
Configuration file
for Allen-Bradley PLCs
• EIP
Configuration File for DXM 1xx-BxR1 and R3 models (p/n
194730
)
• Activating a Cellular Modem (p/n
b_4419353
)
• Additional technical notes and videos
Technical notes,
configuration examples, and ScriptBasic program examples are available at
www.bannerengineering.com
.
DXM100-S1 Modbus Slave System Overview
Banner's DXM Logic Controller integrates Banner's wireless radio and local I/O for a remote I/O device.
Connectivity
Sure Cross Radios
RS-485 Master
I/O
Universal Inputs
Discrete Outputs
Courtesy Power
Switch Power
Inputs/Outputs
—On-board universal and programmable I/O
ports connect to local sensors, indicators, and control
equipment.
• Universal Inputs
• Discrete outputs
• Courtesy power
• Switch power
• Battery backup
• Solar controller
Connectivity—The integrated Sure Cross
®
wireless radio enables Modbus connectivity to remote sensors, indicators, and control
equipment.
Wired Connectivity
Field Bus: Modbus RS-485 Master
Wireless Connectivity
Sure Cross MultiHop 900 MHz, or MultiHop 2.4 GHz
Sure Cross
®
DXM100-S1 Wireless Modbus Slave
2 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 195454 Rev. E