PXXXXTA SERIES
Revision：29-Jul-16 www.brightking.com
Thyristor Surge Suppressors (TSS) Data Sheet
Description
DO-214AC Thyristor solid state protection thyristor protect
telecommunications equipment such as modems, line cards,
fax machines, and other CPE.
P Series devices are used to enable equipment to meet
various regulatory requirements including GR 1089, ITU
K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968
(formerly known as FCC Part 68).
Features
Compared to surge suppression using other technologies, P Series devices offer absolute surge protection
regardless of the surge current available and the rate of applied voltage (dv/dt). P Series devices:
■ Cannot be damaged by voltage
■ Eliminate hysteresis and heat dissipation typically found with clamping devices
■ Eliminate voltage overshoot caused by fast-rising transients
■ Are non-degenerative
■ Will not fatigue
■ Have low capacitance, making them ideal for high-speed transmission equipment
■ Meets MSL level 1, per J-STD-020
■ Safety certification: UL: E244458
Electrical Parameters
Parameter Definition
V
DRM
Peak Off-state Voltage – maximum voltage that can be applied while maintaining off state
V
S
Switching Voltage – maximum voltage prior to switching to on state
V
T
On-state Voltage – maximum voltage measured at rated on-state current
I
DRM
Leakage Current – maximum peak off-state current measured at V
DRM
I
S
Switching Current – maximum current required to switch to on state
I
T
On-state Current – maximum rated continuous on-state current
I
H
Holding Current – minimum current required to maintain on state
C
O
Off-state Capacitance – typical capacitance measured in off state
I
PP
Peak Pulse Current – maximum rated peak impulse current
I
TSM
Peak One-cycle Surge Current – maximum rated one-cycle AC current
di/dt
Rate of Rise of Current – maximum rated value of the acceptable rate of rise in current
over time
PXXXXTA SERIES
Revision：29-Jul-16 www.brightking.com
Electrical Characteristics
Part
Number
V
DRM
(V)
V
S
(V)
V
T
(V)
I
DRM
(μA)
I
S
(mA)
I
T
(A)
I
H
(mA)
C
O
(pF)
Marking
P0080TA 6 25 4 5 800 2.2 50 50 P008A
P0300TA 25 40 4 5 800 2.2 50 70 P03A
P0640TA 58 77 4 5 800 2.2 150 50 P06A
P0720TA 65 88 4 5 800 2.2 150 50 P07A
P0900TA 75 98 4 5 800 2.2 150 45 P09A
P1100TA 90 130 4 5 800 2.2 150 45 P11A
P1300TA 120 160 4 5 800 2.2 150 45 P13A
P1500TA 140 180 4 5 800 2.2 150 40 P15A
P1800TA 170 220 4 5 800 2.2 150 40 P18A
P2300TA 190 260 4 5 800 2.2 150 35 P23A
P2600TA 220 300 4 5 800 2.2 150 35 P26A
P3100TA 275 350 4 5 800 2.2 150 30 P31A
P3500TA 320 400 4 5 800 2.2 150 30 P35A
Notes:
·All measurements are made at an ambient temperature of 25℃. I
PP
applies to -40℃ through +85℃ temperature range.
·Off-state capacitance(C
O
) is measured at 1 MHz with a 2V bias and is typical value.
·For surge ratings, see table below.
Surge Ratings
Series
I
PP
2×10μs
(A)
I
PP
8×20μs
(A)
I
PP
10×160μs
(A)
I
PP
10×560μs
(A)
I
PP
10×1000μs
(A)
I
TSM
60Hz
(A)
di/dt
(A/μs)
A 150 150 90 50 45 20 500
Thermal Considerations
Package DO-214AC/SMA Symbol Parameter Value Unit
T
J
Operating Junction Temperature -40 to +150 ℃
T
S
Storage Temperature Range -40 to +150
℃
R
θJA
Junction to Ambient on printed circuit 120
℃/W