Technical Data Sheet
BERGQUIST GAP PAD TGP 6000ULM
January-2018
PRODUCT DESCRIPTION
A high performance, 6 W/m-K silicone thermal interface
material with ultra low modulus.
Technology Silicone
Appearance Gray
Reinforcement Carrier Fiberglass
Interface Tack 2 sides
Thickness 1.524 to 3.175mm
Cure Heat cure
Application Thermal management,
TIM (Thermal Interface Material)
Operating Temperature
Range
-60 to 200ºC
FEATURES AND BENEFITS
● Thermally conductive : 6.0 W/m-K
● High-compliance, low compression stress
● Ultra low modulus
BERGQUIST GAP PAD TGP 6000ULM is an extremely soft
gap filling material rated at a thermal conductivity of 6.0 W/m-K.
It is specially formulated for high performance applications
requiring low assembly stress. The material offers exceptional
thermal performance at low pressures due to the unique filler
package and ultra low modulus resin formulation. BERGQUIST
GAP PAD TGP 6000ULM is highly conformal, even to surfaces
with high roughness and/or topography, allowing for excellent
interfacing and wet-out characteristics.
BERGQUIST GAP PAD TGP 6000ULM is offered with a
higher natural inherent tack on both sides of the material,
eliminating the need for thermally-impeding adhesive layers
and allowing for stick-in-place characteristics during assembly.
The top side has minimal tack for ease of handling and rework.
BERGQUIST GAP PAD TGP 6000ULM is supplied with
protective liners on both sides.
TYPICAL APPLICATIONS
● Telecommunications
● ASICs and DSPs
● Consumer electronics
● Thermal modules to heat sinks assembly
TYPICAL PROPERTIES OF CURED MATERIAL
Young's modulus is calculated using 0.01in/min, step rate of
strain with a sample size 0.79 in², after 5 minutes of
compression at 10% strain on a 1mm thickness material
Flammability rating UL94 V-0, in-house testing qualified, UL
certificate pending.
Physical Properties
Hardness, Shore 000, ASTM D2240 60
Heat Capacity, ASTM E1269, J/g-K 1.0
Density, Bulk rubber, ASTM D792, g/cc 3.2
Young's Modulus kPa 41.3
(psi) (6)
Electrical Properties
Dielectric Strength, ASTM D149, VAC >5,000
Dielectric Constant, ASTM D150, 1,000Hz 6.5
Volume Resistivity, ASTM D257, ohm-meter 1×10
10
Thermal Properties
Thermal Conductivity, ASTM D5470, W/(m-K) 6.0
Thermal Impedance, 0.040 inch, ASTM D5470, ºC-in
2
/W:
10% Deflection 0.34
20% Deflection 0.29
30% Deflection 0.26
GENERAL INFORMATION
For safe handling information on this product, consult the Safety
Data Sheet, (SDS).
Not for product specifications
The technical data contained herein are intended as reference
only. Please contact your local quality department for
assistance and recommendations on specifications for this
product.
CONFIGURATIONS AVAILABLE
BERGQUIST GAP PAD TGP 6000ULM is available in the
following configurations:
Sheet size 8" x 16"
Standard Thicknesses 0.060", 0.080", 0.100", 0.125"
Natural tack both sides with fiberglass.
TDS BERGQUIST GAP PAD TGP 6000ULM, January-2018
STORAGE
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 25ºC (±3), 50% RH (±10) for a 12 months
shelf life. Material removed from containers may be
contaminated during use. Do not return product to the original
container. Henkel Corporation cannot assume responsibility for
product which has been contaminated or stored under
conditions other than those previously indicated. If additional
information is required, please contact your local Technical
Service Center or Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
psi x 145 = N/mm²
MPa = N/mm²
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Corporation, Resin Technology
Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
Trademark usage: [Except as otherwise noted] All trademarks in this document
are trademarks and/or registered trademarks of Henkel and its affiliates in the
U.S. and elsewhere.
Reference 1
Americas
+1.888.943.6535
Europe
+32.1457.5611
Asia
+86.21.3898.4800
For the most direct access to local sales and technical support visit: www.henkel.com/electronics